Invacare P9000XDT1818 Owners Manual - Page 63

Anti-tippers

Get Invacare P9000XDT1818 PDF manuals and user guides View all Invacare P9000XDT1818 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

SECTION 14-ANTI-TIPPERS SECTION 14-ANTI-TIPPERS ƽ WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. Installing/Removing/Adjusting Anti-Tippers NOTE: For this procedure, refer to FIGURE 14.1 on page 64. Installing ƽ WARNING Anti-tippers MUST be fully engaged and spring buttons fully protruding out of adjustment holes BEFORE using the wheelchair. Ensure both anti-tippers have the same ground clearance. A 1½ to 2-inch clearance between the bottom of the anti-tipper wheels and the ground/floor MUST be maintained at all times. Anti-tippers MUST be used at all times. When outdoors on wet, soft ground or gravel surfaces, anti-tippers may not provide the same level of protection against tipover. Extra caution must be observed when traversing such surfaces. 1. Press the two release buttons in and insert the anti-tippers with anti-tipper wheels pointing toward the ground/floor into the support tubes until the release buttons lock in place. 2. Measure the distance between the bottom of the anti-tipper wheels and the ground/floor and ensure that it is 1½-2-inches. If necessary, adjust height. To adjust the height of the anti-tippers, refer to Adjusting Height on page 63. Removing 1. Press release buttons in and remove the anti-tippers from the support tubes. Adjusting Height 1. Press the release buttons in and adjust the anti-tippers to the desired height. NOTE: The distance between the bottom of the anti-tipper wheels and the ground/floor MUST be 1½ to 2-inches. NOTE: Both anti-tippers should be adjusted to the same height. Part No. 1118386 63 P9000™ XDT

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
SECTION 14—ANTI-TIPPERS
Part No. 1118386
63
P9000
™
XDT
SECTION 14—ANTI-TIPPERS
±
WARNING
After ANY adjustments, repair or service and BEFORE use, make sure all attaching
hardware is tightened securely - otherwise injury or damage may result.
Installing/Removing/Adjusting Anti-Tippers
NOTE: For this procedure, refer to FIGURE 14.1 on page 64.
Installing
±
WARNING
Anti-tippers MUST be fully engaged and spring buttons fully protruding out of
adjustment holes BEFORE using the wheelchair.
Ensure both anti-tippers have the same ground clearance.
A 1½ to 2-inch clearance between the bottom of the anti-tipper wheels and the
ground/floor MUST be maintained at all times.
Anti-tippers MUST be used at all times. When outdoors on wet, soft ground or
gravel surfaces, anti-tippers may not provide the same level of protection against
tipover. Extra caution must be observed when traversing such surfaces.
1.
Press the two release buttons in and insert the anti-tippers with anti-tipper wheels
pointing toward the ground/floor into the support tubes until the release buttons lock
in place.
2.
Measure the distance between the bottom of the anti-tipper wheels and the
ground/floor and ensure that it is 1½-2-inches. If necessary, adjust height. To adjust the
height of the anti-tippers, refer to Adjusting Height
on page 63.
Removing
1.
Press release buttons in and remove the anti-tippers from the support tubes.
Adjusting Height
1.
Press the release buttons in and adjust the anti-tippers to the desired height.
NOTE: The distance between the bottom of the anti-tipper wheels and the ground/floor MUST be
1½ to 2-inches.
NOTE: Both anti-tippers should be adjusted to the same height.