JVC GYHD110U Instructions - Page 31

USING EXTERNAL COMPONENTS Connecting the Video Signal Cables Clamp filter IEEE1394 switch Wind once IEEE 1394 HDV DV PR PB VIDEO/Y „ Connecting the IEEE1394 Cable To reduce the emission of unwanted radio waves, be sure to attach the provided clamp filter as shown in the figure on the left. • Attach the clamp filter as close to the camcorder as possible, as shown in the figure. • Set the IEEE1394 switch on the left panel of the camcorder. DV : DV format HDV : HDV format DC INPUT LINE OUTPUT IEEE1394 PR IEEE1394 Composite cable IEEE 1394 HDV DV DC INPUT LINE OUTPUT Component cable CHANGE 1394 SWITCH „ Displaying Alarms • CHANGE 1394 SWITCH Displayed when the setting for the input/output video format from the IEEE1394 connector and the setting for the IEEE1394 switch are different. Set the IEEE1394 switch so it matches the video format. PB VIDEO/Y CAUTION When connecting the IEEE1394 cable from/to Camcorder, VCR and other IEEE1394 device, make sure the following instructions, otherwise the IEEE1394 circuit device may be destroyed. • Turn the power of both devices OFF and connect the IEEE1394 cable. • Do not insert incorrectly (in reverse) the IEEE1394 cable end to IEEE1394 port of both devices. • Do not connect the IEEE1394 cable under the condition of static electricity. • Turn the power of both devices OFF when changing the IEEE1394 switch from/to HDV/DV. „ Composite and Component Connections The video signals output from the video signal output connec- tors on this camcorder (VIDEO/Y, PB, PR) are as described below, depending on the settings for the OUTPUT TERMI- NAL item on the VIDEO FORMAT menu screen. AUTO : Automatically switches to a composite or component signal, depending on which cable is connected to the video signal COMPOSITE output terminal and outputs the signal. : Outputs a composite signal regardless of which cable is connected to the video signal output connector. COMPONENT : Outputs a component signal regardless of which cable is connected to the video signal output connector. Output signal when AUTO is set Connector (G: Unconnected F: Connected) VIDEO/Y PB PR F F F F G F F F G F G G Output Signal COMPONENT COMPOSITE COMPONENT COMPOSITE None of the above OFF In addition, you can use the PB TAPE item to set whether to automatically detect the video format of the playback tape or only play back a particular format when playing back a tape. X See page 65. CAUTION • Be careful not to apply excess force to the video signal output terminal when connecting or disconnecting the cable. This will cause poor contact or failure. • To use the automatic signal-switching function while the RCA-BNC conversion connector is in use, unplug the entire connector from the video output terminal. 56 Dubbing with AV Devices 1. Composite cable or Component cable PB VIDEO/Y IEEE 1394 HDV DV LINE OUTPUT connector 1. Audio cable DC INPUT LINE OUTPUT IEEE1394 PR Signal flow Recording unit Signal flow Clamp filter 4. VIDEO FORMAT menu screen 5. AUDIO menu screen USING EXTERNAL COMPONENTS By connecting the video signal output terminal and the LINE OUTPUT terminal on this camcorder to an AV device, analog signal dubbing is possible. 1. Connect the cables. Use the provided cable for the audio cable. To reduce the emission of unwanted radio waves, be sure to attach the provided clamp filter as shown in the figure on the left. • Attach the clamp filter as close to the camcorder as possible, as shown in the figure. 2. Turn both devices on. 3. Set the camcorder to VTR mode. Press the CAM/VTR button. The VTR indicator lights. 4. Set the video output. Set the VIDEO FORMAT menu screen. X See page 64. • HDV PB OUTPUT item: Set the video format to be output from the video output terminal during tape playback. • PB TAPE item: Select whether to automatically detect the playback tape video format or play back only a particular format. Normally, use the "AUTO" setting. • OUTPUT TERMINAL item: Set either component or composite output. Normally, use the "AUTO" setting. 5. Set the audio output. X See page 55. Set the AUDIO/MIC menu screen. X See page 72. • AUDIO MONITOR item: Set stereo audio or mixed audio. • PB AUDIO CH [DV] item: Set the audio channel to be output. • Set the MONITOR SELECT switch. 6. Insert the videocassettes. GY-HD110 : Insert the recorded videocassette. Recording unit : Insert the videocassette to be dubbed to. 7. Press the PLAY/STILL button on the GY-HD110 to start playback. 8. Start recording on the recording unit. For details, see the instructions to the unit used for recording. 9. When dubbing is completed. Stop recording on the recording unit, and then press the STOP button on the GY-HD110 to stop playback. 57