JVC GYHD110U Instructions - Page 47
Others - pro
UPC - 046838027345
View all JVC GYHD110U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 47 highlights
FEATURES OF THE CAMERA SECTION Outputting color bars FULL AUTO switch This camcorder can output three types of color bars, depending on the camera settings. NTSC standard : Outputs color bars compliant with the PAL standard SMPTE standard. : Outputs color bars compliant with the EBU standard. 16:9 screen : Outputs multi-format color bars. USER button To output color bars, make the following settings. 1. Turn the FULL AUTO switch to "OFF". 2. Set the BARS item on the CAMERA OPERATION menu screen to "ON". X See page 66. • Color bars are output. Outputting color bars using the USER buttons 1. Turn the FULL AUTO switch to "OFF". 2. Assign "BARS" to one of the USER1, 2 or 3 buttons. X See "SWITCH MODE Menu Screen" on page 71. 3. Press the USER button to which "BARS" was assigned. • Color bars are output. MEMO • You can select whether to output an audio test signal during color bar output using the TEST TONE item on the AUDIO/MIC [1/2] menu screen. X See page 72. • Color bars are not output when FULL AUTO mode is ON or in VTR mode. OTHERS Warnings and Responses Warnings are displayed on the LCD monitor or the viewfinder if there was a mistaken operation, if the battery or tape is low, or if there is a problem on the VTR. In addition, if the tape or battery is low or the VTR has a problem, the tally lamp flashes (or lights) and an alarm is output from the monitor speaker or PHONES jack. MEMO This camcorder uses microcomputers. It may not operate properly if there is external static or interference. If this happens, turn the power off and then on again. Display Status Action 60/30 24 INHIBIT CHANGE FRAME RATE MENU The FRAME RATE item is set to 50/25, and a tape record- Sets the FRAME RATE item on the VIDEO FORMAT menu ed in 60/30, 24 frame HDV format is played back or it is in- screen to match the frames. put into the IEEE1394 port in VTR mode. X See page 64. 60/30 INHIBIT CHANGE FRAME RATE MENU The FRAME RATE item is set to 50/25, and a tape recorded in 60/30 frame DV format is played back or it is input into the IEEE1394 port in VTR mode. 50/25 INHIBIT CHANGE FRAME RATE MENU The FRAME RATE item is set to 60/30 or 24, and a tape recorded in 50/25 frame HDV/DV format or it is input into the IEEE1394 port in VTR mode. 24 INHIBIT CHANGE The FRAME RATE item is set to 50/25 and, a tape recordFRAME RATE MENU ed in 24 frame DV format is played back or it is input into the IEEE1394 port in VTR mode. DV-60I INVALID! DV-24P INVALID! DV-24PA INVALID! A tape recorded in DV-60I, DV-24P, or DV-24PA format The E model cannot play back tapes recorded in DV-60I, was played back or input into the IEEE1394 connector in DV-24P or DV-24PA format or input into the IEEE1394 con- VTR mode on the E model. nector in VTR mode. DV-50I INVALID! DV-25P INVALID! A tape recorded in DV-50I or DV-25P format was played The U model cannot play back tapes recorded in DV-50I or back or input into the IEEE1394 connector in VTR mode on DV-25P format or input into the IEEE1394 connector in the U model. VTR mode. INVALID TAPE! A computer data tape or a DVC PRO cassette was used. Use a MiniDV videocassette. LP TAPE INVALID!* Tried to play back a tape recorded in LP mode. This camcorder cannot record or play back in LP mode. NO DV SIGNAL* DV signal was not input. Set the IEEE1394 switch to DV and input a DV signal. NO HDV SIGNAL* HDV signal was not input. Set the IEEE1394 switch to HDV and input an HDV signal. COPY INHIBIT* Tried to record a copyguarded signal. Cannot record a copyguarded signal. REC INHIBIT* A tape that cannot be recorded (back switch is set to SAVE) Set the switch on the back of the cassette tape to REC. was inserted. NO TAPE* No videocassette tape is inserted. Insert a cassette tape. LOW VOLTAGE* Battery is low. Charge the battery pack or replace it. TAPE NEAR END* There are less than 3 minutes remaining on the tape (flash- To continue shooting, find a new tape or replace the tape. es only when recording). TAPE END* Displayed when the tape ends. Replace the tape. CHANGE 1394 SWITCH* Recording or playback video format and the IEEE1394 set- Set the IEEE1394 switch correctly, turn the power off and ting is different when connected to the IEEE1394 port. then on again. SWITCH TO VTR MODE* Tried to use the FF or REW button in camera mode. Press the CAM/VTR button to set VTR mode. HEAD CLEANING REQUIRED Displayed when the video head is dirty. (Head clogging was Clean with a special head cleaning tape. detected during an edit search in shooting mode as well as X See page 7. during playback and displayed.) CLEANING TAPE! Displayed when a head cleaning tape is inserted. The display disappears when the head cleaning tape is removed. COPY GUARD!* Tried to play back a copyguarded tape. Cannot play back a copyguarded tape. FAN MOTOR HOUR Over the prescribed fan motor usage time. Please contact your local dealer or JVC. PUSH CASSETTE COVER* The videocassette cover is not firmly shut. Lightly push the top center of the videocassette cover. * When status indications are magnified, warnings are not displayed on the LCD monitor. X See "Magnified Status Indications on the LCD Monitor" on page 26. 88 89