Konica Minolta bizhub PRESS 1250 Watkiss PowerSquare 224 User Manual with side - Page 55

Procedure - Refitting, Step 4 - remove the outer book supports, Step 1 - preparation

Get Konica Minolta bizhub PRESS 1250 PDF manuals and user guides View all Konica Minolta bizhub PRESS 1250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

4 - Standard Tasks - Remove and re-fit the Side-Trimmer Book Supports Step 4 - remove the outer book supports There are two outer book supports. Remove one at a time. Hold each end of the outer book support and lift upwards. Remove the outer book support through the top of the machine. Repeat with the other outer book support. Outer book support Procedure - Refitting Step 1 - preparation Use PAPER SIZE to set the paper width See "PAPER SIZE" on page 20. to 365mm. Then use SIDE TRIM to set the side-trim See "SIDE TRIM" on page 22. dimension to 365mm. Open the top cover of the Side-Trimmer. See Figure 36 on page 49. Step 2 - fit the inner and outer book supports There are two outer book supports and two inner book supports. Re-fit one at a time. Refer to the illustrations on page 48. On each book support, there are semicircular cut outs at each end. Position the cut-outs over the fixing points. Press down on the book support so that it fits onto the fixing points. Fixing Repeat with the other book supports. Watkiss PowerSquare™224 User Manual Cut-out 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
4 - Standard Tasks - Remove and re-fit the Side-Trimmer Book Supports
Watkiss PowerSquare™224 User Manual
51
Procedure - Refitting
Step 4 - remove the outer book supports
There are two outer book supports.
Remove one at a time.
Hold each end of the outer book support
and lift upwards.
Remove the outer book support through
the top of the machine.
Repeat with the other outer book sup-
port.
Outer book support
Step 1 - preparation
Use
PAPER SIZE
to set the paper width
to 365mm.
Then use
SIDE TRIM
to set the side-trim
dimension to 365mm.
See “PAPER SIZE” on page 20.
See “SIDE TRIM” on page 22.
Open the top cover of the Side-Trimmer.
See Figure 36 on page 49.
Step 2 - fit the inner and outer book supports
There are two outer book supports and
two inner book supports.
Re-fit one at a time.
Refer to the illustrations on page 48.
On each book support, there are semi-
circular cut outs at each end.
Position the cut-outs over the fixing
points.
Press down on the book support so that
it fits onto the fixing points.
Repeat with the other book supports.
Fixing
Cut-out