Lexmark 7675 Fax Guide - Page 50

Printer receives a blank fax, Received fax has poor print quality, Fax Setup, Dialing and Sending - reviews

Page 50 highlights

MAKE SURE THE PRINTER DETECTS DIAL TONE • See the instructions for sending a fax while listening to a call (on hook dial). • Check the Dial Method setting. 1 Listen for a dial tone. If you hear a dial tone but the printer hangs up without dialing, this means it did not recognize the dial tone. 2 From the printer control panel, press . 3 Press the up or down arrow button until Fax Setup is highlighted, and then press OK. 4 Press the up or down arrow button until Dialing and Sending is highlighted, and then press OK. 5 Press the up or down arrow button until Dial Method is highlighted, and then press OK. 6 Press the up or down arrow button until Behind PBX (Dial Tone Detect Off) is highlighted, and then press OK to save the setting. Printer receives a blank fax These are possible causes and solutions. Try one or more of the following: CHECK ORIGINAL DOCUMENT Ask the sender to verify the original document was loaded correctly. CHECK INK Check the ink levels, and install a new print cartridge if necessary. CHECK CARTRIDGES 1 Remove the print cartridges. 2 Make sure the sticker and tape have been removed. 1 2 3 Reinsert the print cartridges. Received fax has poor print quality These are possible solutions. Try one or more of the following: REVIEW CHECKLIST FOR SENDER • Check that the quality of the original document is satisfactory. • Resend the fax. There may have been a problem with the quality of the telephone line connection. • Increase the fax scan resolution. Troubleshooting 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54

M
AKE
SURE
THE
PRINTER
DETECTS
DIAL
TONE
See the instructions for sending a fax while listening to a call (on hook dial).
Check the Dial Method setting.
1
Listen for a dial tone. If you hear a dial tone but the printer hangs up without dialing, this means it did not
recognize the dial tone.
2
From the printer control panel, press
.
3
Press the up or down arrow button until
Fax Setup
is highlighted, and then press
OK
.
4
Press the up or down arrow button until
Dialing and Sending
is highlighted, and then press
OK
.
5
Press the up or down arrow button until
Dial Method
is highlighted, and then press
OK
.
6
Press the up or down arrow button until
Behind PBX (Dial Tone Detect Off)
is highlighted,
and then press
OK
to save the setting.
Printer receives a blank fax
These are possible causes and solutions. Try one or more of the following:
C
HECK
ORIGINAL
DOCUMENT
Ask the sender to verify the original document was loaded correctly.
C
HECK
INK
Check the ink levels, and install a new print cartridge if necessary.
C
HECK
CARTRIDGES
1
Remove the print cartridges.
2
Make sure the sticker and tape have been removed.
1
2
3
Reinsert the print cartridges.
Received fax has poor print quality
These are possible solutions. Try one or more of the following:
R
EVIEW
CHECKLIST
FOR
SENDER
Check that the quality of the original document is satisfactory.
Resend the fax. There may have been a problem with the quality of the telephone line connection.
Increase the fax scan resolution.
Troubleshooting
50