Lexmark 7675 Fax Guide - Page 52

Remote Fax Error, Phone Line Busy, Fax Setup, Dialing and Sending, Max Send Speed, Redial Attempts

Page 52 highlights

Remote Fax Error These are possible causes and solutions. Try one or more of the following: CHECK PHONE LINE Resend the fax. There may have been a problem with the quality of the telephone line connection. LOWER THE TRANSMISSION SPEED 1 From the printer control panel, press . 2 Press the up or down arrow button until Fax Setup is highlighted, and then press OK. 3 Press the up or down arrow button until Dialing and Sending is highlighted, and then press OK. 4 Press the up or down arrow button until Max Send Speed is highlighted, and then press OK. 5 Press the up or down arrow button to select a lower transmission speed, and then press OK. 6 Press . 7 Resend the fax. 8 If the problem persists, repeat step 1 through step 5 to resend the fax at successively lower transmission speeds. Note: 2400 bps is the lowest transmission speed. Notes: • The lower the transmission speed, the longer it will take your fax to print. • This solution will reduce the speed for future faxes until you reset the transmission speed. Phone Line Busy These are possible causes and solutions. Try one or more of the following: CHANGE REDIAL SETTINGS The printer automatically redials three times at 2-minute intervals. You can change the default settings to redial up to five times at intervals up to 8 minutes. To change the redial settings: 1 From the printer control panel, press . 2 Press the up or down arrow button until Fax Setup is highlighted, and then press OK. 3 Press the up or down arrow button until Dialing and Sending is highlighted, and then press OK. 4 To change the number of times the printer will redial: a Press the up or down arrow button until Redial Attempts is highlighted, and then press OK. b Press the up or down arrow button until the setting you want is highlighted, and then press OK. Troubleshooting 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54

Remote Fax Error
These are possible causes and solutions. Try one or more of the following:
C
HECK
PHONE
LINE
Resend the fax. There may have been a problem with the quality of the telephone line connection.
L
OWER
THE
TRANSMISSION
SPEED
1
From the printer control panel, press
.
2
Press the up or down arrow button until
Fax Setup
is highlighted, and then press
OK
.
3
Press the up or down arrow button until
Dialing and Sending
is highlighted, and then press
OK
.
4
Press the up or down arrow button until
Max Send Speed
is highlighted, and then press
OK
.
5
Press the up or down arrow button to select a lower transmission speed, and then press
OK
.
6
Press
.
7
Resend the fax.
8
If the problem persists, repeat step 1 through step 5 to resend the fax at successively lower transmission speeds.
Note:
2400 bps is the lowest transmission speed.
Notes:
The lower the transmission speed, the longer it will take your fax to print.
This solution will reduce the speed for future faxes until you reset the transmission speed.
Phone Line Busy
These are possible causes and solutions. Try one or more of the following:
C
HANGE
REDIAL
SETTINGS
The printer automatically redials three times at 2-minute intervals. You can change the default settings to redial
up to five times at intervals up to 8 minutes.
To change the redial settings:
1
From the printer control panel, press
.
2
Press the up or down arrow button until
Fax Setup
is highlighted, and then press
OK
.
3
Press the up or down arrow button until
Dialing and Sending
is highlighted, and then press
OK
.
4
To change the number of times the printer will redial:
a
Press the up or down arrow button until
Redial Attempts
is highlighted, and then press
OK
.
b
Press the up or down arrow button until the setting you want is highlighted, and then press
OK
.
Troubleshooting
52