Lexmark E330 Service Manual - Page 88

Service Manual, Operator panel service check continued

Get Lexmark E330 PDF manuals and user guides View all Lexmark E330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

4505 Operator panel service check (continued) FRU Operator panel Controller card Warning: Do not replace the operator panel and controller card at the same time. Each card contains the printer settings. When either of these cards is new, it obtains the settings from the other card. Settings are lost when both are new and replaced at the same time. Action Lights If none of the lights come on, make sure the cable is properly connected to the controller card and the controller card has input voltage to it. Verify +24 V dc on cable pin 8 at J7. • Check for +5 V dc at J16, pin 5 See "Controller card service check" on page 2-49 or page 5-3 for more information. • If these voltages are not correct, replace the controller card. • If these voltages are correct, replace the operator panel. If more than one light does not turn on or an individual light stays on solid during POST, replace the operator panel. If all lights are dim and operate erratically during POST or all lights come on and stay on solid during POST, replace the FRUs in the following order one at a time: • Controller card • Operator panel 2-60 Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
2-60
Service Manual
4505
Operator panel service check (continued)
FRU
Action
Operator panel
Controller card
Warning:
Do not
replace the
operator panel and
controller card at the
same time. Each card
contains the printer
settings. When either
of these cards is new,
it obtains the settings
from the other card.
Settings are lost when
both are new and
replaced at the same
time.
Lights
If none of the lights come on, make
sure the cable is properly connected
to the controller card and the
controller card has input voltage to it.
Verify +24 V dc on cable pin 8 at J7.
•
Check for +5 V dc at J16, pin 5
See
“Controller card service
check” on page
2-49
or
page 5-3
for more information.
•
If these voltages are not correct,
replace the controller card.
•
If these voltages are correct,
replace the operator panel.
If more than one light does not turn
on or an individual light stays on
solid during POST, replace the
operator panel.
If all lights are dim and operate
erratically during POST or all lights
come on and stay on solid during
POST, replace the FRUs in the
following order one at a time:
•
Controller card
•
Operator panel