Lexmark T642 User's Guide - Page 13

Installing drivers for local printing, Setting parameters in the printer, Reports, Menu Settings - driver for windows 7

Get Lexmark T642 - Monochrome Laser Printer PDF manuals and user guides
UPC - 734646722001
View all Lexmark T642 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installing drivers for local printing Before you can print, you must establish communication between the printer and computer. To do this: 1 Set serial parameters in the printer. 2 Install a printer driver on the attached computer. 3 Match the serial settings in the COM port. Setting parameters in the printer 1 Press on the operator panel. 2 Press until Reports appears, and then press . Note: For information about serial menus and messages, see the publications CD that shipped with the printer. 3 Press until Menu Settings Page appears, and then press . The printer returns to Ready. 4 Press . 5 Press until Network/Ports appears, and then press . 6 Press until Serial Standard or Serial Option X appears, and then press . (x) is the number of the serial port. 7 Press until press . appears (where is the parameter required for a change), and then 8 Press until appears (where is the setting required for a change), and then press . Note the following restrictions: • Maximum baud rate supported is 115,200. • Data Bits must be set to 7 or 8. • Parity must be set to Even, Odd, or None. • Stop Bits must be set to 2. • Flow Control recommended protocol setting is Xon/Xoff. 9 Press . The printer returns to Serial or Serial x. 10 Print a Menu Settings page, and verify the serial parameters are correct. Note: Keep this page for later use. a Press on the operator panel. b Press until Reports appears, and then press . c Press until Menu Settings Page appears, and then press . d Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the serial parameters. Windows 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Windows
13
Installing drivers for local printing
Before you can print, you must establish communication between the printer and computer. To do this:
1
Set serial parameters in the printer.
2
Install a printer driver on the attached computer.
3
Match the serial settings in the COM port.
Setting parameters in the printer
1
Press
on the operator panel.
2
Press
until
Reports
appears, and then press
.
Note:
For information about serial menus and messages, see the publications CD that shipped with the
printer.
3
Press
until
Menu Settings Page
appears, and then press
.
The printer returns to
Ready
.
4
Press
.
5
Press
until
Network/Ports
appears, and then press
.
6
Press
until
Serial Standard
or
Serial Option X
appears, and then press
.
(
x
) is the number of the serial port.
7
Press
until
<Parameter>
appears (where
<Parameter>
is the parameter required for a change), and then
press
.
8
Press
until
<Setting>
appears (where
<Setting>
is the setting required for a change), and
then press
.
Note the following restrictions
:
•
Maximum baud rate supported is 115,200.
•
Data Bits must be set to 7 or 8.
•
Parity must be set to Even, Odd, or None.
•
Stop Bits must be set to 2.
•
Flow Control recommended protocol setting is Xon/Xoff.
9
Press
.
The printer returns to
Serial
or
Serial x
.
10
Print a Menu Settings page, and verify the serial parameters are correct.
Note:
Keep this page for later use.
a
Press
on the operator panel.
b
Press
until
Reports
appears, and then press
.
c
Press
until
Menu Settings Page
appears, and then press
.
d
Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the
serial parameters.