Onkyo TX-NR709 Owner Manual - Page 47

Note • If the "Speakers Type(Front)" setting is set to "Bi-Amp", Powered Zone 2 cannot be used. • When the "Powered Zone 2" setting is set to "Yes", the surround back, front wide and front high speakers cannot be used. Speaker Configuration This setting is set automatically by Audyssey MultEQ® XT Room Correction and Speaker Setup function (➔ page 31). With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify "Full Band" for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey MultEQ XT Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to "80Hz(THX)" crossover. Note • These settings are not available in either of the following cases: - a pair of headphones is connected. - the "Audio TV Out" setting is set to "On" (➔ page 59). - "HDMI Control(RIHD)" is set to "On" (➔ page 58) and you're listening through your TV speakers. ■ Subwoofer ` Yes ` No ■ Front `Full Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz Note • If the "Subwoofer" setting is set to "No", the "Front" setting is fixed to "Full Band". ■ Center*1, Surround*1, Surround Back*2*3*4 `Full Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None ■ Front Wide*1*2*4, Front High*1*2*4 `Full Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None Note *1 "Full Band" can be selected only when "Full Band" is selected in the "Front" setting. *2 If the "Surround" setting is set to "None", this setting cannot be selected. *3 If the "Surround" setting is set to anything other than "Full Band", "Full Band" cannot be selected here. *4 If the "Speakers Type(Front)" setting is set to "Bi-Amp", or the "Powered Zone 2" setting is set to "Yes", this setting cannot be selected. ■ Surround Back Ch ` 1ch: Select if only one surround back speaker L is connected. ` 2ch: Select if two (left and right) surround back speakers are connected. Note • If the "Surround Back" Setting is set to "None", this setting cannot be selected. ■ LPF of LFE (Low-Pass Filter for the LFE Channel) ` 80Hz, 90Hz, 100Hz, 120Hz ` Bypass: Low-Pass Filter is not applied. With this setting, you can specify the cutoff frequency of the LFE channel's low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel. Note • If you're using THX-certified speakers, select "80Hz". ■ Double Bass This setting is NOT set automatically by Audyssey MultEQ XT Room Correction and Speaker Setup function (➔ page 31). ` On ` Off(THX) Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Note • This function can be set only if the "Subwoofer" setting is set to "Yes", and the "Front" setting is set to "Full Band". • If you're using THX-certified speakers, select "Off(THX)". ■ Subwoofer Phase ` 0º ` 180º: Moves the subwoofer phase. Note • If the "Subwoofer" setting is set to "No", this setting cannot be selected (➔ page 47). En 47