Onkyo TX-NR709 Owner Manual - Page 76
Video, Tuner, Remote Controller, an HDMI - connection error
View all Onkyo TX-NR709 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 76 highlights
■ The beginning of audio received by an HDMI IN can't be heard Since it takes longer to identify the format of an - HDMI signal than it does for other digital audio signals, audio output may not start immediately. ■ The on screen display does not appear Depending on the input signal, the on screen display 57 may not appear when the input signal from the HDMI IN is output to a device connected to the HDMI OUT MAIN. Video ■ There's no picture Make sure that all video connecting plugs are pushed 16 in all the way. Make sure that each video component is properly 17, 18 connected. If your TV is connected to the HDMI output(s), 45 select in the "HDMI Input" setup to watch composite video, S-Video and component video sources. If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to either the HDMI output(s) or COMPONENT VIDEO MONITOR OUT. 18, 44 If the video source is connected to a composite video 18 input, your TV must be connected to the HDMI output(s) or the corresponding composite video output. If the video source is connected to an HDMI input, 17, 45 you must assign that input to an input selector, and your TV must be connected to the HDMI output(s). While the Pure Audio listening mode is selected, the - video circuitry is turned off and only video signals input through HDMI IN can be output. On your TV, make sure that the video input to which - the AV receiver is connected is selected. If the "Monitor Out" setting is set to "Both(Main)" - or "Both(Sub)" while your TV is connected to a secondary HDMI output (not a primary HDMI output), the picture may not appear. In this case, change the setting to "Both". ■ There's no picture from a source connected to an HDMI IN Reliable operation with an HDMI-to-DVI adapter is 88 not guaranteed. In addition, video signals from a PC are not guaranteed. When the resolution is set to any resolution not 45 supported by the TV, no video is output from the HDMI outputs. If the message "Resolution Error" appears on the - AV receiver's display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player. ■ The on-screen menus don't appear On your TV, make sure that the video input to which - the AV receiver is connected is selected. When the AV receiver is not connected to a TV via - HDMI, onscreen menus are not displayed. En 76 Tuner ■ Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn't light Relocate your antenna. - Move the AV receiver away from your TV or - computer. Listen to the station in mono. 28 When listening to an AM station, operating the - remote controller may cause noise. Passing cars and airplanes can cause interference. - Concrete walls weaken radio signals. - If nothing improves the reception, install an outdoor - antenna. Remote Controller ■ The remote controller doesn't work Before operating this unit, be sure to press - RECEIVER. Make sure that the batteries are installed with the 4 correct polarity. Install new batteries. Don't mix different types of 4 batteries, or old and new batteries. Make sure that the remote controller is not too far 4 away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor. Make sure that the AV receiver is not subjected to - direct sunshine or inverter-type fluorescent lights. Relocate if necessary. If the AV receiver is installed in a rack or cabinet - with colored-glass doors, the remote controller may not work reliably when the doors are closed. Make sure you've selected the correct remote controller mode. 11, 70 When using the remote controller to control other - manufacturers' AV components, some buttons may not work as expected. Make sure you've entered the correct remote control 69 code. Make sure to set the same ID on both the AV 57 receiver and remote controller. ■ Can't control other components If it's an Onkyo component, make sure that the V 20 cable and analog audio cable are connected properly. Connecting only an V cable won't be enough. Make sure you've selected the correct remote controller mode. 11, 70 For a proper operation of the remote controller as a 41 cassette tape deck is connected to the TV/CD IN jack, or as an RI Dock is connected to the TV/CD IN, VCR/DVR IN or GAME IN jacks, you must set the input display accordingly. If you cannot operate it, you will need to enter the 69 appropriate remote control code.