Panasonic SDRS150 SDRS150 User Guide - Page 20

To set quick start function, To cancel quick start, Turning the unit on/off continued

Get Panasonic SDRS150 - SD MOVIE CAMERA PDF manuals and user guides
UPC - 037988254460
View all Panasonic SDRS150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Turning the unit on/off (continued) To set quick start function SETUP DISPLAY DATE/TIME DATE FORMAT FORMAT CARD QUICK START SETUP ENTER 1 1/3 OFF ON EXIT MENU 2 A B Press the menu button B, use the cursor button A to select [ SETUP]#[ QUICK START], and then set the function to [ON]. (P27) When the LCD monitor is closed, the quick start standby mode is established. 1 The status indicator lights green. ≥ If quick start is set, the lens cover does not close. If the quick start function is set When the LCD monitor is opened, the unit goes into recording standby. 2 When the LCD monitor is opened, the status indicator lights red. To cancel quick start Press the menu button, use the cursor button to select [ [ QUICK START]#[OFF]. (P27) SETUP]# ≥ Turn off the power to cancel quick start standby. The status indicator goes out and the power turns off. ≥ Quick start standby is canceled after 5 minutes have elapsed. In this case, turn off the power and then turn it on again or open the LCD monitor again. The unit cannot be quick-started and it takes longer for it to start operating. ≥ Quick start standby is canceled and the power turns off if the mode dial is switched to a mode other than motion picture recording mode or still picture recording mode. ≥ Since about half the power of normal recording is used in quick start standby, using quick start reduces the recordable time. ≥ If quick start is not set, it takes longer for this unit to start operating, but the amount of power consumed when the LCD monitor is closed is reduced. ≥ When the LCD monitor is opened in quick start standby status, the zoom magnification is set to the 1k (approximately). This may cause the size of the image to be different from the size before standby status was established. ≥ When this unit is quick-started with the white balance on automatic, it may take some time until the white balance is adjusted if the scene being recorded has a light source different from the scene last recorded. (When the MagicPix function is used, however, the white balance of the scene last recorded is retained.) 20 VQT0X39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
20
VQT0X39
To set quick start function
Press the menu button
B
, use the
cursor button
A
to select
[
SETUP]
#
[
QUICK START], and
then set the function to [ON]. (P27)
When the LCD monitor is closed, the quick start
standby mode is established.
1
The status indicator lights green.
≥
If quick start is set, the lens cover does not
close.
If the quick start function is set
When the LCD monitor is opened, the unit goes
into recording standby.
2
When the LCD monitor is opened, the status
indicator lights red.
To cancel quick start
Press the menu button, use the cursor button to select [
SETUP]
#
[
QUICK START]
#
[OFF]. (P27)
Turning the unit on/off (continued)
MENU
SETUP
ENTER
EXIT
DISPLAY
FORMAT CARD
DATE/TIME
QUICK START
SETUP
OFF
ON
1/3
DATE FORMAT
1
2
A
B
≥
Turn off the power to cancel quick start
standby. The status indicator goes out
and the power turns off.
≥
Quick start standby is canceled after
5 minutes have elapsed.
In this case, turn off the power and then
turn it on again or open the LCD monitor
again. The unit cannot be quick-started
and it takes longer for it to start operating.
≥
Quick start standby is canceled and the
power turns off if the mode dial is
switched to a mode other than motion
picture recording mode or still picture
recording mode.
≥
Since about half the power of normal
recording is used in quick start standby,
using quick start reduces the recordable
time.
≥
If quick start is not set, it takes longer for
this unit to start operating, but the
amount of power consumed when the
LCD monitor is closed is reduced.
≥
When the LCD monitor is opened in
quick start standby status, the zoom
magnification is set to the 1
k
(approximately). This may cause the size
of the image to be different from the size
before standby status was established.
≥
When this unit is quick-started with the
white balance on automatic, it may take
some time until the white balance is
adjusted if the scene being recorded has
a light source different from the scene
last recorded. (When the MagicPix
function is used, however, the white
balance of the scene last recorded is
retained.)