Pfaff creative vision Owner's Manual - Page 27

Bobbin winding

Get Pfaff creative vision PDF manuals and user guides View all Pfaff creative vision manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Bobbin winding Winding from horizontal position 1. Place an empty bobbin on the bobbin spindle, with the logo facing up. Use only the original PFAFF® bobbins approved for this model. 2. Place the thread spool on the spool pin in horizontal position. Slide a spool cap tightly against the spool. 3. Place the thread into the thread guide (A) from front to back. Pull the thread counter-clockwise above the bobbin winder thread guide (B) and then through the bobbin thread guides (C) at the rear. Note: Make sure the thread is pulled securely inside the pre-tension device for correct thread tension. 4. Thread through the slot in the bobbin (D) from the inside to the outside. 5. Push the bobbin winder lever towards the bobbin to wind. A pop-up appears on the screen. To adjust winding speed, use the slider in the pop-up. Stop and start bobbin winding with the icons in the pop-up. Hold the end of the thread firmly when starting to wind. When the bobbin is full, the bobbin winder lever will switch back and the winding will stop automatically. The pop-up closes. Remove the bobbin and cut the thread using the bobbin thread cutter. Cut the free thread end close to the bobbin. Winding while threaded Make sure that the presser foot and the needle are in the up position. To prevent the needle from bending, pull the thread out of the needle. Bring the thread up from the needle thread guide (D), upward through the left-hand threading slot and through the bobbin thread guides (E). Then follow step 4 and 5 above. B C A D E A D 2:7 Preparations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
2:7
D
D
B
C
A
E
A
Preparations
Bobbin winding
Winding from horizontal position
1.
Place an empty bobbin on the bobbin spindle,
with the logo facing up. Use only the original
PFAFF® bobbins approved for this model.
2.
Place the thread spool on the spool pin in
horizontal position. Slide a spool cap tightly
against the spool.
3.
Place the thread into the thread guide (A) from
front to back. Pull the thread counter-clockwise
above the bobbin winder thread guide (B) and
then through the bobbin thread guides (C) at
the rear.
Note: Make sure the thread is pulled securely inside
the pre-tension device for correct thread tension.
4.
Thread through the slot in the bobbin (D) from
the inside to the outside.
5.
Push the bobbin winder lever towards the
bobbin to wind. A pop-up appears on the
screen. To adjust winding speed, use the slider
in the pop-up. Stop and start bobbin winding
with the icons in the pop-up. Hold the end of
the thread
fi
rmly when starting to wind.
When the bobbin is full, the bobbin winder
lever will switch back and the winding will
stop automatically. The pop-up closes. Remove
the bobbin and cut the thread using the bobbin
thread cutter. Cut the free thread end close to
the bobbin.
Winding while threaded
Make sure that the presser foot and the needle
are in the up position. To prevent the needle from
bending, pull the thread out of the needle.
Bring the thread up from the needle thread guide
(D), upward through the left-hand threading slot
and through the bobbin thread guides (E).
Then
follow step 4 and 5 above.