Pioneer SC-67 Owner's Manual - Page 74

09 Using other functions Setting the Audio options There are a number of additional sound settings you can make using the AUDIO PARAMETER menu. The defaults, if not stated, are listed in bold. Important ! Note that if a setting doesn't appear in the AUDIO PARAMETER menu, it is unavailable due to the current source, settings and status of the receiver. 1 Press to the receiver operation mode, then press AUDIO PARAMETER. 2 Use i/j to select the setting you want to adjust. Depending on the current status/mode of the receiver, certain options may not be able to be selected. Check the table below for notes on this. 3 Use k/l to set as necessary. See the table below for the options available for each setting. 4 Press RETURN to confirm and exit the menu. Audio parameter menu Setting What it does MCACC (MCACC preset) Selects your favorite MCACC preset memory when multiple preset memories are saved. When an MCACC preset memory has been renamed, the given name is displayed. EQ (Acoustic Calibration EQ) S-WAVE (Standing Wave) PHASE C+ (Phase Control Plus) DELAY (Sound Delay) TONE (Tone Control) BASS TREBLE Switches on/off the effects of EQ Pro. Switches on/off the effects of Standing Wave Control. For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first place. This function corrects for phase shifting on such discs. This function is especially effective when playing music. When AUTO is selected, the LFE channel's delay is measured automatically and the disc is played with the optimum correction. Some monitors have a slight delay when showing video, so the soundtrack will be slightly out of sync with the picture. By adding a bit of delay, you can adjust the sound to match the presentation of the video. Applies the treble and bass tone controls to a source, or bypasses them completely. Adjusts the amount of bass. Adjusts the amount of treble. Option(s) c M1. MEMORY 1 to M6. MEMORY 6 d Default: M1. MEMORY 1 ON OFF ON OFF c AUTO/0 to 16 (ms) d Default: AUTO c 0.0 to 10.0 (frames) d 1 second = 30 frames (NTSC) Default: 0.0 BYPASS ON c -6 to +6 (dB) d Default: 0 (dB) c -6 to +6 (dB) d Default: 0 (dB) Setting S.RTRV (Auto Sound Retriever) DNR (Digital Noise Reduction) DIALOG E (Dialog Enhancement) Hi-bit32 DFILTER (Digital Filter) DUAL (Dual Mono) Fixed PCM DRC (Dynamic Range Control) Loud Mgmt (Loudness Management) What it does Option(s) With the Auto Sound Retriever function, DSP processing is used to OFF compensate for the loss of audio data upon compression, improving the sound's sense of density and modulation. Also, when a player supporting the Sound Retriever Link function is connected to the receiver by HDMI, by setting this to ON, the bitrate ON information of the compressed audio file being played on the player is acquired using the Control with HDMI function, and the sound is optimized based on this information (Sound Retriever Link). May improve the quality of sound in a noisy source (for example, video OFF tape with lots of background noise) when switched on. This only has an effect with 2-channel signal inputs. This mode is effective for contents with a sampling frequency of 48 ON kHz or less. Localizes dialog in the center channel to make it stand out from other background sounds in a TV or movie soundtrack. By moving from UP1 through UP2 and UP3 up to UP4, you can make the sound source seem to relocate upwards. c OFF/FLAT/UP1/UP2/ UP3/UP4 d Default: OFF Creates a wider dynamic range with digital sources like CDs, DVDs or ON BDs. 16-, 20- and 24-bit PCM as well as compressed audio is requan- tized to 32 bits, and the high frequency component is interpolated upon data processing to enable smoother, more subtle musical OFF expression. Switches the AUDIO DAC (Digital Audio Converter) digital filter type. One of three settings can be selected: SLOW (soft and warm), SHARP (solid and tight) and SHORT (quick and forward). SLOW (Hi-Sampling) SHARP SHORT CH1 - Channel 1 is heard only Specifies how dual mono encoded Dolby Digital soundtracks should be played. Dual mono is not widely used, but is sometimes necessary when two languages need to be sent to separate channels. CH2 - Channel 2 is heard only CH1 CH2 - Both channels heard from front speakers This is useful if you find there is a slight delay before OFF recognizes OFF the PCM signal on a CD, for instance. When ON is selected, noise may be output during playback of non- ON PCM sources. Please select another input signal if this is a problem. Adjusts the level of dynamic range for movie soundtracks optimized for Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, DTS-HD and DTS-HD Master Audio (you may need to use this feature when listening to surround sound at low volumes). AUTO MAX MID OFF Adjusts the level of dynamic range for movie soundtracks optimized ON for Dolby TrueHD (you may need to use this feature when listening to surround sound at low volumes). This can only be set when DRC is set to OFF and the input signal is a OFF Dolby TrueHD signal. 74