Schwinn 510e Elliptical Service Manual - Page 61

Disconnect the Speed Sensor and Power Input Cables from the Servo

Get Schwinn 510e Elliptical PDF manuals and user guides View all Schwinn 510e Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

11. Using a #2 Phillips screwdriver, remove the indicated screws (by ovals) from the Left Upper Engine Shroud. Note: T he Power Inlet is attached to the inside of the Left Upper Engine Shroud. Do not crimp the Power Inlet Cable. 12. Remove the Left Upper Engine Shroud. 13. Using a #2 Phillips screwdriver, remove the 4 screws that attach each of the Lower Engine Shrouds, and remove them. Left Upper Engine Shroud Power Inlet Lower Engine Shroud, Left 14. Disconnect the Speed Sensor and Power Input Cables from the Servo Motor. Connectors are indicated by ovals. Note: D o not crimp the Cables. 15. Insert 2.5" x 10" cardboard between the Brake Magnet and the Flywheel, and tape the cardboard to the Brake Magnet. Note: Be sure the cardboard covers all of the Brake Magnet. The cardboard will keep the Brake Magnet from grabbing onto the Flywheel. 16. Using a #2 Phillips screwdriver, remove the two screws that attach the Servo Motor Bracket to the Servo Motor. Speed Sensor Cable 17. Using two 8mm open faced wrenches, loosen both of the securing nuts that secure the Brake Cable to the Brake Arm. 18. Push the Brake Arm toward the Servo Motor and slide the Brake Cable out of the Brake Arm. 19. Using a #2 Phillips screwdriver, remove the four screws that attach the Servo Motor to the Frame Assembly. Power Input Cable Servo Motor 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
61
11. Using a #2 Phillips screwdriver, remove the indicated screws (by
ovals) from the Left Upper Engine Shroud.
Note:
The Power Inlet is attached to the inside of the Left Upper Engine
Shroud. Do not crimp the Power Inlet Cable.
12. Remove the Left Upper Engine Shroud.
13. Using a #2 Phillips screwdriver, remove the 4 screws that attach each
of the Lower Engine Shrouds, and remove them.
14. Disconnect the Speed Sensor and Power Input Cables from the Servo
Motor. Connectors are indicated by ovals.
Note:
Do not crimp the Cables.
15. Insert 2.5” x 10” cardboard between the Brake Magnet and the Fly
-
wheel, and tape the cardboard to the Brake Magnet.
Note:
Be sure the cardboard covers all of the Brake Magnet. The card-
board will keep the Brake Magnet from grabbing onto the Flywheel.
16. Using a #2 Phillips screwdriver, remove the two screws that attach the
Servo Motor Bracket to the Servo Motor.
17. Using two 8mm open faced wrenches, loosen both of the securing
nuts that secure the Brake Cable to the Brake Arm.
18. Push the Brake Arm toward the Servo Motor and slide the Brake
Cable out of the Brake Arm.
19. Using a #2 Phillips screwdriver, remove the four screws that attach the
Servo Motor to the Frame Assembly.
Left Upper Engine
Shroud
Power Inlet
Lower Engine Shroud,
Left
Servo Motor
Power Input
Cable
Speed Sensor
Cable