Schwinn 510e Elliptical Service Manual - Page 62

Connect the Servo Motor Cable to the Console Mast Cable,

Get Schwinn 510e Elliptical PDF manuals and user guides View all Schwinn 510e Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

20. Cut the Zip-Tie that secures the Servo Motor Cable to the Frame Assembly. 21. Tie a piece of string or wire to the end of the old Servo Motor Cable where it attached to the I/O Cable from the Console Mast. 22. Grasp the lower end of the old Servo Motor Cable and carefully pull it down through the Frame Assembly. Untie the string from the old Servo Motor Cable. 23. Using a #2 Phillips screwdriver, remove the four screws that attach the Servo Motor to the Frame Assembly. 24. Replace the old Servo Motor with the new Servo Motor. 25. Connect the new Servo Motor Cable to the piece of string or wire through the Frame Assembly. Note: D o not crimp the Cable. 26. Hold the upper end of the string and carefully pull the new Servo Motor Cable through the Frame Assembly. Note: Do not crimp the cables. 27. Untie the string from the new Servo Motor Cable. Note: Do not crimp the Cable. 28. Connect the Servo Motor Cable to the Console Mast Cable, and attach the Console Mast. Note: Do not crimp the Cable. Zip Tie Brake Cable Servo Motor Bracket Servo Motor Brake Arm 29. Re-assemble the machine in the reverse order of when the parts were removed. 30. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
62
20. Cut the Zip-Tie that secures the Servo Motor Cable to the Frame
Assembly.
21. Tie a piece of string or wire to the end of the old Servo Motor Cable
where it attached to the I/O Cable from the Console Mast.
22. Grasp the lower end of the old Servo Motor Cable and carefully pull
it down through the Frame Assembly. Untie the string from the old Servo
Motor Cable.
23. Using a #2 Phillips screwdriver, remove the four screws that attach
the Servo Motor to the Frame Assembly.
24. Replace the old Servo Motor with the new Servo Motor.
25. Connect the new Servo Motor Cable to the piece of string or wire
through the Frame Assembly.
Note:
Do not crimp the Cable.
26. Hold the upper end of the string and carefully pull the new Servo Mo-
tor Cable through the Frame Assembly.
Note:
Do not crimp the cables.
27. Untie the string from the new Servo Motor Cable.
Note:
Do not crimp the Cable.
28. Connect the Servo Motor Cable to the Console Mast Cable, and
attach the Console Mast.
Note:
Do not crimp the Cable.
29. Re-assemble the machine in the reverse order of when the parts were
removed.
30. Final Inspection
Inspect your machine to ensure that all hardware is tight and components
are properly assembled.
Do not use until the machine has been fully assembled and
inspected for correct performance in accordance with the
Owner’s Manual.
Servo Motor
Brake Cable
Brake Arm
Zip Tie
Servo Motor Bracket