Sharp MX-B350P MX-B350P MX-B450P User Manual - Page 97

Problem, Cause and solution, ENERGY SAVE] indicator

Get Sharp MX-B350P PDF manuals and user guides View all Sharp MX-B350P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

TROUBLESHOOTING►TROUBLESHOOTING Problem Paper misfeed. Paper size for a paper tray cannot be set. A print job stops before it is finished. The display turns off. Lighting fixture flickers. Cause and solution The paper is outside of the specified size and weight range. → Use paper within the specified range. Paper curled or damp. → Do not use curled or crimped paper. Replace with dry paper. During periods when the machine is not used for a long time, remove the paper from the tray and store it in a dark place in a bag to prevent moisture absorption. Paper is not loaded properly. → Make sure the paper is properly installed. Pieces of paper inside machine. → Remove all pieces of misfed paper. Several sheets of paper stick together. → Fan the paper well before loading it. A paper misfeed has occurred in the tray. → Turn the paper over and/or turn it around, and reload. Too much paper is loaded in the tray. → If the stack of paper is higher than the indicator line on the tray, remove some of the paper and reload so that the stack does not exceed the line. The guides on the bypass tray do not match the width of the paper. → Adjust the guides to match the width of the paper. If the paper guide presses too hard against the paper, a misfeed may occur. Adjust the guide so that it lightly contacts the paper. The bypass tray extension is not pulled out. → When loading paper, open the extension. The bypass paper feed roller is dirty. → Clean the roller. Printing is performed. Set the paper size after printing is complete. The machine has stopped temporarily due to running out of paper or a misfeed. → Load paper or remove the misfeed, and then set the paper size. The paper output tray is full. → Remove the output in the paper output tray to resume printing. The tray is out of paper. → Load paper. Any other indicators turned off. → If other indicators are lit, the machine is in "Preheat mode". Press any key on the operation panel to resume normal operation. [ENERGY SAVE] indicator ( ) blinks. → The machine is in auto power shut-off mode. Press the [ENERGY SAVE] key ( ) to resume normal operation. The same power outlet being used is for the lighting fixture and the machine. → Connect the machine to a power outlet which is not used for other electric appliances. 3-4 Page 1-15 - 1-15 3-8 - 3-14 1-19 1-22 1-22 1-29 - 3-8 - 1-15 1-11 1-10 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
3-4
TROUBLESHOOTING
►
TROUBLESHOOTING
Paper misfeed.
The paper is outside of the specified size and weight range.
→
Use paper within the specified range.
1-15
Paper curled or damp.
→
Do not use curled or crimped paper. Replace with dry paper.
During periods when the machine is not used for a long time,
remove the paper from the tray and store it in a dark place in a
bag to prevent moisture absorption.
–
Paper is not loaded properly.
→
Make sure the paper is properly installed.
1-15
Pieces of paper inside machine.
→
Remove all pieces of misfed paper.
3-8
Several sheets of paper stick together.
→
Fan the paper well before loading it.
–
A paper misfeed has occurred in the tray.
→
Turn the paper over and/or turn it around, and reload.
3-14
Too much paper is loaded in the tray.
→
If the stack of paper is higher than the indicator line on the tray,
remove some of the paper and reload so that the stack does not
exceed the line.
1-19
The guides on the bypass tray do not match the width of the
paper.
→
Adjust the guides to match the width of the paper.
If the paper guide presses too hard against the paper, a misfeed
may occur. Adjust the guide so that it lightly contacts the paper.
1-22
The bypass tray extension is not pulled out.
→
When loading paper, open the extension.
1-22
The bypass paper feed roller is dirty.
→
Clean the roller.
1-29
Paper size for a paper tray cannot be
set.
Printing is performed.
Set the paper size after printing is complete.
–
The machine has stopped temporarily due to running out of
paper or a misfeed.
→
Load paper or remove the misfeed, and then set the paper size.
3-8
A print job stops before it is finished.
The paper output tray is full.
→
Remove the output in the paper output tray to resume printing.
–
The tray is out of paper.
→
Load paper.
1-15
The display turns off.
Any other indicators turned off.
→
If other indicators are lit, the machine is in "Preheat mode". Press
any key on the operation panel to resume normal operation.
1-11
[ENERGY SAVE] indicator (
) blinks.
→
The machine is in auto power shut-off mode. Press the [ENERGY
SAVE] key (
) to resume normal operation.
1-10
Lighting fixture flickers.
The same power outlet being used is for the lighting fixture and
the machine.
→
Connect the machine to a power outlet which is not used for other
electric appliances.
–
Problem
Cause and solution
Page