Sony HDWM2100/20 Operation Manual - Page 19

Switch Panel, Shot mark

Get Sony HDWM2100/20 PDF manuals and user guides View all Sony HDWM2100/20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Chapter 2 Location and Function of Parts 7 LEARN button After setting a speed variation start point (STUNT IN point) and a speed variation end point (STUNT OUT point), pressing this button makes the tape start running. You can then use the search dial to vary the tape speed, which is automatically stored in memory. After thus storing the tape speed variation in memory, pressing this button starts an automatic playback between the speed variation start and end points at the stored speed. qa Shot mark section 1 LIST button Use this button to read in and list shot marks. 2 REC/ERASE indicator This lights in the state in which writing, amending, and deleting of shot marks is enabled and flashes while a shot mark is actually being written, amended or deleted. 3 MARK button Hold this button down for 2 seconds or more, to enable writing, amending, and deleting of shot marks. 1 LIST button LIST GOOD SHOT MARK REC/ ERASE 2 REC/ERASE indicator 3 MARK button 2-1-3 Switch Panel To access the switch panel, open the lower control panel. On how to open the lower control panel, see the figure on page 2-1. 1 Memory card slot 2 Memory card ejection button 3 CONTROL PANEL connector KEY INHI PANEL SEL CONTROL PANEL ON OFF REAR FRONT 4 PANEL SELECT switch 5 KEY INHI switch 6 Memory stick slot 2-11 Chapter 2 Location and Function of Parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
Chapter 2
Location and Function of Parts
Chapter 2
Location and Function of Parts
2-11
7
LEARN button
After setting a speed variation start point (STUNT IN
point) and a speed variation end point (STUNT OUT
point), pressing this button makes the tape start
running. You can then use the search dial to vary the
tape speed, which is automatically stored in memory.
After thus storing the tape speed variation in memory,
pressing this button starts an automatic playback
between the speed variation start and end points at the
stored speed.
qa
Shot mark section
LIST GOOD SHOT MARK
REC/
ERASE
1
LIST button
3
MARK button
2
REC/ERASE indicator
1
LIST button
Use this button to read in and list shot marks.
2
REC/ERASE indicator
This lights in the state in which writing, amending, and
deleting of shot marks is enabled and flashes while a
shot mark is actually being written, amended or
deleted.
3
MARK button
Hold this button down for 2 seconds or more, to enable
writing, amending, and deleting of shot marks.
2-1-3
Switch Panel
To access the switch panel, open the lower control
panel.
On how to open the lower control panel, see the figure on
page 2-1.
ON
OFF
KEY INHI
FRONT
REAR
PANEL SEL
CONTROL PANEL
5
KEY INHI switch
4
PANEL SELECT switch
3
CONTROL PANEL connector
2
Memory card ejection button
1
Memory card slot
6
Memory stick slot