Sony HDWM2100/20 Operation Manual - Page 93

Item number, Item name, Settings, CUEUP, PEAK0, REF.0, to FF, SILNC

Get Sony HDWM2100/20 PDF manuals and user guides View all Sony HDWM2100/20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Menu items in the range 800 to 899, relating to audio control Item number Item name Settings 801 DIGITAL JOG SOUND Turns the digital jog sound on and off. OFF: Digital jog sound is turned off. Audio of digital channels not subjected to speed correction is output. When the tape stops, after one second the audio is muted. ON : Digital jog sound is turned on. When the tape speed is in the range ×-1 to ×+1 (for Betacam SX playback, in the range ×-1 to ×+2), speed correction is carried out, and the same jog sound as a conventional analog VTR is output. 802 DIGITAL AUDIO MUTING Set the digital audio muting conditions during shuttle playback. IN SHUTTLE MODE OFF : Not muted. CUEUP: Muted during cue-up or preroll operations. FULL: Muted in shuttle mode. 805 AUDIO MONITOR Select the audio mixing method used for digital audio signals and Betacam OUTPUT MIXING playback analog audio signals supplied to the MONITOR OUTPUT connector. ADD: Simple addition RMS : Root-mean-square AVE: Simple average 806 LEVEL METER SCALE Select the mode in which digital audio levels are displayed. PEAK0 : Displays the audio level as negative values with the maximum level set to 0 dB. REF.0: Displays the audio level as positive and negative values with the reference level set to 0 dB. 807 AUDIO OUTPUT PHASE Select the output timing of digital audio playback signals (HDSDI, SDI, and AES/ EBU only). The reference position corresponds to a setting of 80H; when the setting is less than 80H, the output timing is advanced, and when it is higher than 80H, the output timing is delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1 sample=approx. 20 µs) 0 to 80 to FF : Setting in this range 808 INTERNAL AUDIO Select the operation of the internal audio test signal generator. SIGNAL GENERATOR OFF : No operation SILNC: Silent signal 1KHZ: At 1 kHz, -20 dB FS sine wave is supplied to all audio input channels. 809 AUDIO LEVEL METER Set the brightness of the audio level meters. DIMMER CONTROL 0 to 7: Set in this range. 0 is the brightest, and 7 the dimmest. 823 NON-AUDIO FLAG PB Controls the non-audio flag when the playback format is Digital Betacam or (Invalid in 24PsF or Betacam SX. 23.98PsF mode.) Sub-item 1 CH1/CH2 2 CH3/CH4 During playback (except E-E mode), sets the digital audio non-audio flag as follows. OFF : OFF (the data is audio) ON: ON (the data is non-audio) AUTO: As follows, depending on whether tape data has been confirmed. • Tape data has been read and confirmed: ON or OFF, according to the data. • Tape data has not been confirmed: Current state is maintained. Notes • In the Betacam SX format, audio signals only are recorded. Therefore, the nonaudio flag is OFF. • During playback of analog tapes, the non-audio flag is OFF regardless of the setting of this item. • In the MPEG IMX format, the non-audio flag follows the setting of maintenance menu item M372 during recording, playback, and E-E mode. For more information about the maintenance menu item M372, refer to the Maintenance Manual. (Continued) Chapter 9 Setup Menus 9-23 Chapter 9 Setup Menus

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
Chapter 9
Setup Menus
Chapter 9
Setup Menus
9-23
Menu items in the range 800 to 899, relating to audio control
Item number
Item name
Settings
802
DIGITAL AUDIO MUTING
IN SHUTTLE MODE
Set the digital audio muting conditions during shuttle playback.
OFF :
Not muted.
CUEUP:
Muted during cue-up or preroll operations.
FULL:
Muted in shuttle mode.
801
DIGITAL JOG SOUND
Turns the digital jog sound on and off.
OFF:
Digital jog sound is turned off.
Audio of digital channels not subjected to speed correction is output. When the
tape stops, after one second the audio is muted.
ON :
Digital jog sound is turned on.
When the tape speed is in the range
×
–1 to
×
+1 (for Betacam SX playback, in the
range
×
–1 to
×
+2), speed correction is carried out, and the same jog sound as a
conventional analog VTR is output.
Select the mode in which digital audio levels are displayed.
PEAK0 :
Displays the audio level as negative values with the maximum level set
to 0 dB.
REF.0:
Displays the audio level as positive and negative values with the
reference level set to 0 dB.
805
AUDIO MONITOR
OUTPUT MIXING
Select the audio mixing method used for digital audio signals and Betacam
playback analog audio signals supplied to the MONITOR OUTPUT connector.
ADD:
Simple addition
RMS :
Root-mean-square
AVE:
Simple average
806
LEVEL METER SCALE
807
AUDIO OUTPUT PHASE
Select the output timing of digital audio playback signals (HDSDI, SDI, and AES/
EBU only).
The reference position corresponds to a setting of 80H;
when the
setting is less than 80H, the output timing is advanced, and when it is higher than
80H, the output timing is delayed.
(at 80H, 128 samples = approx. 2.7 ms, and 1
sample=approx. 20 μs)
0 to
80
to FF :
Setting in this range
808
INTERNAL AUDIO
SIGNAL GENERATOR
Select the operation of the internal audio test signal generator.
OFF :
No operation
SILNC:
Silent signal
1KHZ:
At 1 kHz, –20 dB FS sine wave is supplied to all audio input channels.
809
AUDIO LEVEL METER
DIMMER CONTROL
Set the brightness of the audio level meters.
0
to 7:
Set in this range.
0 is the brightest, and 7 the dimmest.
823
NON-AUDIO FLAG PB
(Invalid in 24PsF or
23.98PsF mode.)
Controls the non-audio flag when the playback format is Digital Betacam or
Betacam SX.
Sub-item
1
CH1/CH2
During playback (except E-E mode), sets the digital audio non-audio flag as
follows.
OFF :
OFF (the data is audio)
ON:
ON (the data is non-audio)
AUTO:
As follows, depending on whether tape data has been confirmed.
• Tape data has been read and confirmed: ON or OFF, according to the data.
• Tape data has not been confirmed: Current state is maintained.
Notes
• In the Betacam SX format, audio signals only are recorded. Therefore, the non-
audio flag is OFF.
• During playback of analog tapes, the non-audio flag is OFF regardless of the
setting of this item.
• In the MPEG IMX format, the non-audio flag follows the setting of maintenance
menu item M372 during recording, playback, and E-E mode.
For more information about the maintenance menu item M372, refer to the
Maintenance Manual.
2
CH3/CH4
(Continued)