Sony KP-46WT520 Operating Instructions - Page 81

Audio, General, MUTING, Speaker, TV FUNCTION, Auto SAP, Stereo, Audio Out, Fixed, Variable., RESET - blinking

Get Sony KP-46WT520 - Wide Screen Projection Tv PDF manuals and user guides View all Sony KP-46WT520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Welcome SETUP SETUP Audio Problem Possible Remedies Good picture, ❏ Press MUTING so that Muting disappears from the screen (see page 44). no sound ❏ Make sure the Speaker option is set to On in the Audio Menu (see page 65). Cannot gain enough volume ❏ Increase the volume of the cable box using the cable box's remote control. when using a cable box Then press TV FUNCTION and adjust the TV's volume. Sound seems weak or ❏ The TV's audio might be set to Auto SAP or Mono, when it might be better set insufficient to Stereo. In the Audio Menu (see page 64), set the MTS setting to Stereo. If already set to Stereo, switch to Mono (which may reduce background noise during weak stereo broadcasts). Cannot raise the volume on ❏ If the Speaker option is set to Off and the Audio Out option is set to Fixed (in external audio speakers order to output the sound to your audio system) use your audio receiver to adjust the sound (see page 64). Or, to use the TV remote control, set the Audio Out option to Variable. ❏ To turn on the TV speakers, set the Speaker option to On (see page 64). General Problem Possible Remedies How to reset TV to ❏ Turn on the TV. While holding down the RESET button on the remote factory settings control, press the POWER button on the TV. (The TV will turn itself off, then back on again.) Release the RESET button. How to restore Video settings ❏ Press the RESET button on the remote control while in the Video Menu (see to factory settings page 63). How to restore Audio ❏ Press the RESET button on the remote control while in the Audio Menu (see settings to factory settings page 65). Cannot cycle through the ❏ Be sure the Video Label option is not set to Skip (see page 73). other video equipment connected to the TV Cannot operate Menu ❏ If a menu option appears in gray, this indicates that the TV is in a state in which the menu option is not available. Lost password ❏ In the password screen (see page 69), enter the following master password: 4357. The master password clears your previous password; it cannot be used to temporarily unblock channels. LED on front panel is lit ❏ The STAND BY LED (see page 12) blinks when the TV is turned on, then shuts off when the picture is displayed. If the LED blinks continuously, this may indicate the TV needs service. ❏ The TIMER LED (see page 12) indicates that the timer is set. When the timer is set, this LED will remain lit even when the TV is turned off. Other Info Other Info Other Info 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
80
Other Info
Other Info
Welcome
Other Info
SETUP
SETUP
Audio
General
Problem
Possible Remedies
Good picture,
no sound
❏
Press
MUTING
so that
Muting
disappears from the screen (see page 44).
❏
Make sure the
Speaker
option is set to
On
in the Audio Menu (see page 65).
Cannot gain enough volume
when using a cable box
❏
Increase the volume of the cable box using the cable box’s remote control.
Then press
TV FUNCTION
and adjust the TV’s volume.
Sound seems weak or
insufficient
❏
The TV’s audio might be set to
Auto SAP
or
Mono
, when it might be better set
to
Stereo
. In the Audio Menu (see page 64), set the
MTS
setting to
Stereo
. If
already set to
Stereo,
switch to
Mono
(which may reduce background noise
during weak stereo broadcasts).
Cannot raise the volume on
external audio speakers
❏
If the
Speaker
option is set to
Off
and the
Audio Out
option is set to
Fixed
(in
order to output the sound to your audio system) use your audio receiver to
adjust the sound (see page 64). Or, to use the TV remote control, set the
Audio Out
option to
Variable.
❏
To turn on the TV speakers, set the
Speaker
option to
On
(see page 64).
Problem
Possible Remedies
How to reset TV to
factory settings
❏
Turn on the TV. While holding down the
RESET
button on the remote
control, press the
POWER
button on the TV. (The TV will turn itself off, then
back on again.) Release the
RESET
button.
How to restore Video settings
to factory settings
❏
Press the
RESET
button on the remote control while in the Video Menu (see
page 63).
How to restore Audio
settings to factory settings
❏
Press the
RESET
button on the remote control while in the Audio Menu (see
page 65).
Cannot cycle through the
other video equipment
connected to the TV
❏
Be sure the
Video Label
option is not set to
Skip
(see page 73).
Cannot operate Menu
❏
If a menu option appears in gray, this indicates that the TV is in a state in
which the menu option is not available.
Lost password
❏
In the password screen (see page 69), enter the following master password:
4357
. The master password clears your previous password; it cannot be
used to temporarily unblock channels.
LED on front panel is lit
❏
The STAND BY LED (see page 12) blinks when the TV is turned on, then
shuts off when the picture is displayed. If the LED blinks continuously, this
may indicate the TV needs service.
❏
The TIMER LED (see page 12) indicates that the timer is set. When the
timer is set, this LED will remain lit even when the TV is turned off.