Sony LF-B1 Operating Instructions (LF-PK1) - Page 12

Base Station Modes, Normal mode, Setup mode, Status for registration

Get Sony LF-B1 PDF manuals and user guides View all Sony LF-B1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Setup and Connections Base Station Modes The base station has a normal mode and a setup mode. Press the base station power switch Normal mode (SETUP MODE LED off) • You can use NetAV at home and away from home. SETUP MODE LED Off • You can make base station settings via a wireless connection. • You cannot make base station settings.* * You can make settings via a router if you set [Security] in the [Advanced Setup] page (1 page 36) to [Enable at all times (Security Level: Low)]. You can also make base station settings via a wireless connection. SETUP MODE button Press the SETUP MODE button on the rear panel of the base station. Keep pressing until the SETUP MODE LED starts blinking. • When the base station reboots. • When the base station settings page has not been accessed for 15 minutes. Setup mode (SETUP MODE LED on) On • You cannot use NetAV at home and away from home. • You can make base station settings.* * Use the SSID and WEP key on the sticker of the base station for a wireless connection in setup mode. Also, a wireless LAN uses a channel in the 2.4 GHz band when the base station is in setup mode. Status for registration (SETUP MODE LED blinking) Blinking • You can register LocationFree devices only during the first 5 minutes after the base station is in setup mode. (The base station is still in setup mode after this 5-minute state.) • If the 5-minute registration state ends before you finish, switch to the registration status by pressing and holding the SETUP MODE button again until the SETUP MODE LED starts blinking. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Setup and Connections
12
The base station has a normal mode and a setup mode.
Base Station Modes
Normal mode
(SETUP MODE LED off)
•
You can use NetAV at home and away from home.
•
You can make base station settings via a wireless connection.
•
You cannot make base station settings.*
*
You can make settings via a router if you set [Security] in the [Advanced Setup] page
(
1
page
36) to [Enable at all times (Security Level: Low)]. You can also make base station
settings via a wireless connection.
Press the base station power switch
SETUP MODE button
Press the SETUP MODE
button on the rear panel
of the base station.
Keep pressing until the
SETUP MODE LED starts
blinking.
•
When the base station reboots.
•
When the base station settings
page has not been accessed for
15 minutes.
Setup mode
(SETUP MODE LED on)
•
You cannot use NetAV at home and away from home.
•
You can make base station settings.*
*
Use the SSID and WEP key on the sticker of the base station for a wireless connection in setup
mode.
Also, a wireless LAN uses a channel in the 2.4 GHz band when the base station is in setup
mode.
SETUP MODE LED
Status for registration
(SETUP MODE LED blinking)
•
You can register LocationFree devices only during the first 5 minutes after
the base station is in setup mode. (The base station is still in setup mode
after this 5-minute state.)
•
If the 5-minute registration state ends before you finish, switch to the
registration status by pressing and holding the SETUP MODE button
again until the SETUP MODE LED starts blinking.
On
Blinking
Off