Home » Toshiba Manuals » UPS » Toshiba T42F3F500XAMBN » Manual Viewer

Toshiba T42F3F500XAMBN User Manual - Page 21

Caution

View all Toshiba T42F3F500XAMBN manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

TOSHIBA 13) Additional warnings and notifications shall be posted at the equipment installation location as deemed required by Qualified Personnel. CAUTION When the UPS is in the Inverter mode, turning the breaker to the OFF position will cause the unit to go into the battery backup mode. The UPS will continue to provide power to the load. The unit must be in Bypass mode and then the breaker turned to the OFF position for the UPS to shut down power to the load. CAUTION Do not EPO (Emergency Power OFF) the UPS and then reset the breaker until the UPS has been fully discharged. The UPS could be damaged if the unit is not fully powered down before the breaker is reset. 4.0 UPS Connections 4.1 Power Connections 4.1.1 Power Connections 15/25/30 kVA with Internal Batteries The following illustrates the wiring connections from the power distribution panel (not part of the UPS) to the terminal block of the 15/25/30 kVA UPS Models CUSTOMER-PROVIDED AC DISTRIBUTION PANEL TB1 Optional Bypass Input: 3-phase, 3-Wire *208 V requires 3-phase, TB4 4-Wire Wye INPUT GROUND RESISTANCE LESS THAN 10 OHMS 4200FA CT/XT User's Manual 20

Section	Page
TABLE OF CONTENTS	3
1.0 Product Description	15
1.1 Theory of Operation	15
1.2 Application and Use	15
1.3 Power Backup	15
1.4 Power Conditioning	15
2.0 Unpacking/Inspection/Storage/Disposal	16
2.1 Unpacking the new UPS equipment 15/25/30 kVA:	16
2.2 Unpacking the new UPS equipment 50 kVA:	17
2.3 Inspection of the new UPS equipment	17
2.4 Storage of UPS equipment	18
2.5 Disposal	18
3.0 Installation Precautions	19
3.1 Equipment Placement	19
3.2 System Preparation (Pre-Power)	20
3.3 Operating Precautions	20
4.0 UPS Connections	21
4.1 Power Connections	21
4.1.1 Power Connections 15/25/30 kVA with Internal Batteries	21
4.1.2 Power Connections 15/25/30 kVA with Internal Transformer	22
4.1.3 Recommended Wire Size and Torque Requirements	23
4.1.4 Power Connection Cable Routing and Conduit Placement 15/25/30 kVA	24
	25
4.2 Control Circuit and External Battery Interface Connections 15/25/30 kvA	25
	25
4.2.1 Recommended Wire Size and Torque Requirements	25
4.3 Power Connections 50 kVA	26
4.3.1 Recommended Wire Size and Torque Requirements For UPS Input and Output Terminals	27
	27
4.3.2 Power Connection Cable Routing and Conduit Placement 50 kVA	28
4.4 Control Circuit and External Interface Connections 50 kVA	29
4.4.1 Recommended Wire Size and Torque Requirements	29
4.5 Communication Interface	30
4.5.1 Remote Contact	30
4.5.2 RS-232C	31
4.5.3 UPS Shutdown (via RS-232C)	31
5.0 Specifications	32
5.1 4200FA 15 / 25 kVA @ 208 VAC Input/ 208 VAC Output w/Internal Batteries	32
5.2 4200FA 15/25 kVA w/Internal Transformer	33
5.3 4200FA 30 kVA @ 208 VAC Input/ 208 VAC Output w/Internal Batteries	34
5.4 4200FA 30 kVA w/Internal Transformer	35
5.5 4200FA 50kVA @ 208 VAC Input/ 208 VAC Output w/Internal Batteries	36
5.6 4200FA 50kVA w/Internal Transformer	37
6.0 Operating the UPS	38
6.1 AC Input Mode (Normal Operation)	38
6.2 Bypass Mode	39
6.4 Battery Backup Mode	40
6.5 Battery Backup Time and Discharge Process	41
6.6 Battery Low Voltage Tolerances	41
6.7 Battery Recharging	42
6.8 Front Panel Layout (All Units)	43
6.9 EPO (Emergency Power Off) Function	43
6.10 Audible Alarm Functions	44
6.11 LED (Light Emitting Diode) Functions	44
6.11.1 LED (Light Emitting Diode) System Status	45
6.12 LCD (Liquid Crystal Display) Functions	45
6.12.1 Line-1 System Messages	45
6.12.2 Line-2 System Fault Messages	46
6.12.3 Line-3 System Messages	46
6.12.4 Line-4 System Messages	46
6.13 Initial Battery Charge	47
6.14 Start-up Procedure	48
6.15 Shutdown Procedure	49
6.16 Maintenance Bypass Procedure	49
6.17 Keypad Overview	51
6.18 Key Functions	52
6.18.1 MONI	52
6.18.2 IN	52
6.18.3 OUT	52
6.18.4 BATT Key	53
6.18.5 MENU, F1, ENTER, UP, & DOWN Keys	53
6.18.6 BATT TEST Key	53
6.18.7 BUZZ STOP Key	54
6.18.8 RESET Key	54
6.19 Menu Data Screens	55
6.19.1 Settings for Calendar and Clock	55
6.19.2 Adjusting the Buzzer Volume	55
6.19.3 Settings for Display Duration	55
6.19.4 Run Switch Select	56
6.19.5 Serial Com Station Address	56
6.19.6 Output Voltage Adjustment	57
6.19.7 Equalize Charge Mode Select	57
6.19.8 Reset to Default Settings	58
6.20 Overload Operation	58
6.21 Backup History and Fault History	59
7.0 UPS Protection System	61
7.1 System Protection Features	61
7.2 System Protection Functions	61
8.0 Start-up/Scheduled Maintenance/Part Replacement	62
8.1 Start-up	62
8.2 Preventive Maintenance	62
8.3 Parts Replacement	63
9.0 External Dimensions / Shipping Dimensions / Weights	64
9.1 External Dimensions 15/25/30 kVA	64
9.2 External Dimensions 50kVA	65