Yamaha HTR 6230 Owner's Manual - Page 46

Dolby Digital or DTS, played. Dolby Digital - problems

Get Yamaha HTR 6230 - AV Receiver PDF manuals and user guides
UPC - 027108933054
View all Yamaha HTR 6230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Troubleshooting Problem Cause Remedy Sound is heard from the speaker on one side only. Incorrect cable connections. Incorrect settings in "SP LEVEL." Connect the cables properly. If the problem persists, the cables may be defective. Adjust the "SP LEVEL" settings. Only the center speaker outputs substantial sound. When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, and the front and surround speakers output effect sounds. No sound is heard from the center speaker. "CENTER" in "SPEAKER SET" is set to Set "CENTER" to "SML" or "LRG." "NONE." Some sound field programs do not output Try another sound field program. sounds from the center speaker. No sound is heard from the surround speakers. "SUR. LR" in "SPEAKER SET" is set to "NONE." This unit is in the "STRAIGHT" mode and a monaural source is being played back. Set "SUR. LR" to "SML" or "LRG." Press MSTRAIGHT on the front panel so that "STRAIGHT" disappears from the front panel display. No sound is heard from the subwoofer. "BASS OUT" in "SPEAKER SET" is set to "FRNT" when a Dolby Digital or DTS signal is being played. Set "BASS OUT" to "SWFR" or "BOTH." "BASS OUT" in "SPEAKER SET" is set to "SWFR" or "FRNT" when a 2-channel source is being played. Set "BASS OUT" to "BOTH." The source does not contain lowfrequency bass signals. Dolby Digital or DTS sources cannot be played. (Dolby Digital or DTS indicator on the front panel display does not light up.) The connected component is not set to output Dolby Digital or DTS digital signals. Audio input jack select is set to "ANALOG." Make an appropriate setting following the operating instructions for your component. Set Audio input jack select to "AUTO." A humming sound is Incorrect cable connections. heard. Connect the audio cables firmly. If the problem persists, the cables may be defective. The volume level cannot be increased, or the sound is distorted. You are attempting to set the volume level Adjust "MAX VOL." setting. higher than the maximum volume level. The component connected to the AUDIO Turn on the power of the component. OUT (REC) jack on this unit is turned off. The sound effect cannot be recorded. It is not possible to record the sound effect with a recording component. A source cannot be recorded by an analog component connected to the AUDIO OUT (REC) jack. The source component is not connected to Connect the source component to the analog AUDIO the analog AUDIO IN jacks on this unit. IN jacks. See page 11-14 33 32 25 32 26 32 32 - 18 - 34 - 13 42 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
42
En
Troubleshooting
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11-14
Incorrect settings in “SP LEVEL.”
Adjust the “SP LEVEL” settings.
33
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER” in “SPEAKER SET” is set to
“NONE.”
Set “CENTER” to “SML” or “LRG.”
32
Some sound field programs do not output
sounds from the center speaker.
Try another sound field program.
25
No sound is heard
from the surround
speakers.
“SUR. LR” in “SPEAKER SET” is set to
“NONE.”
Set “SUR. LR” to “SML” or “LRG.”
32
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press
M
STRAIGHT
on the front panel so that
“STRAIGHT” disappears from the front panel
display.
26
No sound is heard
from the subwoofer.
“BASS OUT” in “SPEAKER SET” is set
to “FRNT” when a Dolby Digital or DTS
signal is being played.
Set “BASS OUT” to “SWFR” or “BOTH.”
32
“BASS OUT” in “SPEAKER SET” is set
to “SWFR” or “FRNT” when a 2-channel
source is being played.
Set “BASS OUT” to “BOTH.”
32
The source does not contain low-
frequency bass signals.
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator on
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG.”
Set Audio input jack select to “AUTO.”
18
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level
higher than the maximum volume level.
Adjust “MAX VOL.” setting.
34
The component connected to the AUDIO
OUT (REC) jack on this unit is turned off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jack.
The source component is not connected to
the analog AUDIO IN jacks on this unit.
Connect the source component to the analog AUDIO
IN jacks.
13
Problem
Cause
Remedy
See
page