Yamaha RX Z9 MCXSP10 Manual - Page 94

Changing source names in the display window, ballpoint pen or similar

Get Yamaha RX Z9 - AV Receiver PDF manuals and user guides
UPC - 027108918204
View all Yamaha RX Z9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

EXIT TOP SOURCE INPUT MODE ENTER PURE DIRECT TITLE MULTI CH IN DVD DVR VCR 2 DTV/LD VCR 1 CD SAT MD/TAPE CD-R CABLE V-AUX TUNER PHONO STANDBY SYSTEM POWER MACRO TRANSMIT RE-NAME CLEAR LEARN MACRO OFF ON REMOTE CONTROL FEATURES 6 Press and hold the button you want to program on the remote control for your component until "OK" appears in the display window. Notes • "NG" appears in the display window if programming was unsuccessful. In this case, start over from step 5. • This remote control can learn approximately 120 functions. However depending on the signals learned, "FULL" may appear in the display before you have programmed 120 functions. In this case, clear unnecessary programmed functions to make room for further learning. 7 Repeat steps 5 and 6 to program additional functions. 8 Press LEARN again to exit from the learning mode. LEARN Changing source names in the display window You can change the name that appears in the display window on the remote control if you want to use a different name to the one that is factory preset. This is useful when you have set the input selector to control another component. 1 Press an input selector button to select the source component you want to rename. The selected component name appears in the display window. V-AUX TUNER PHONO CABLE SAT MD/TAPE CD-R CD DTV/LD VCR 1 VCR 2 DVR DVD 2 Press RE-NAME using a ballpoint pen or similar RE-NAME object. 3 Press k/n to select and enter a character. Pressing n changes the character as follows: A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash). (Pressing k changes the characters in reverse order.) ENTER Notes • Learning may not be possible in the following cases: - When the batteries in the remote control for this unit or other components are weak. - When the distance between the two remote controls is too great or too small. - When the remote control infrared windows are not aimed at an appropriate angle. - When the remote control is exposed to direct sunlight. - When the function to be programmed is continuous or uncommon. • "ERROR" appears in the display window if you press more than one button at the same time. 4 Press l / h to move the cursor to the next position. ENTER y If you want to continue setting up names for other components, press ENTER and repeat steps 1, 3 and 4. 5 Press RE-NAME again to exit from the renaming mode. RE-NAME 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
90
REMOTE CONTROL FEATURES
6
Press and hold the button you want to
program on the remote control for your
component until “OK” appears in the display
window.
•
“NG” appears in the display window if programming was
unsuccessful. In this case, start over from step 5.
•
This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display before you have programmed 120
functions. In this case, clear unnecessary programmed functions
to make room for further learning.
7
Repeat steps 5 and 6 to program additional
functions.
8
Press LEARN again to exit from the learning
mode.
•
Learning may not be possible in the following cases:
– When the batteries in the remote control for this unit or other
components are weak.
– When the distance between the two remote controls is too
great or too small.
– When the remote control infrared windows are not aimed at
an appropriate angle.
– When the remote control is exposed to direct sunlight.
– When the function to be programmed is continuous or
uncommon.
•
“ERROR” appears in the display window if you press more than
one button at the same time.
You can change the name that appears in the display
window on the remote control if you want to use a
different name to the one that is factory preset. This is
useful when you have set the input selector to control
another component.
1
Press an input selector button to select the
source component you want to rename.
The selected component name appears in the display
window.
2
Press RE-NAME using a
ballpoint pen or similar
object.
3
Press
k
/
n
to select and enter a character.
Pressing
n
changes the character as follows:
A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash).
(Pressing
k
changes the characters in reverse order.)
4
Press
l
/
h
to move the cursor to the next
position.
y
If you want to continue setting up names for other
components, press ENTER and repeat steps 1, 3 and 4.
5
Press RE-NAME again to exit from the
renaming mode.
Notes
Notes
TRANSMIT
RE-NAME
STANDBY
TUNER
MULTI CH IN
PURE DIRECT
TOP
EXIT
INPUT MODE
SYSTEM
CLEAR
LEARN
MACRO
OFF
ON
MACRO
PHONO
CD
DVD
DVR
VCR 2
TITLE
SOURCE
ENTER
DTV/LD
VCR 1
CD-R
MD/TAPE
SAT
CABLE
POWER
V-AUX
LEARN
Changing source names in the
display window
TUNER
PHONO
CD
DVD
DVR
VCR 2
DTV/LD
VCR 1
CD-R
MD/TAPE
SAT
CABLE
V-AUX
RE-NAME
ENTER
ENTER
RE-NAME