Yamaha YSP800S Owner's Manual - Page 92

Problem, Cause, Remedy, Dolby Digital or DTS sources

Get Yamaha YSP800S - Digital Sound Projector Five CH Speaker PDF manuals and user guides
UPC - 027108923543
View all Yamaha YSP800S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

TROUBLESHOOTING Problem Cause Remedy Surround sound effects are insubstantial. The listening room is not a regular shape. Install this unit in a square or rectangular shaped room. There is no wall in the path of the sound Try placing a flat object, such as a board, beam. in the path of the sound beam. Dolby Digital or DTS sources cannot be played. (Dolby Digital or DTS indicator does not light up in the front panel display.) The connected component is not set to output Dolby Digital or DTS digital signals. The input mode is set to ANALOG. Make an appropriate setting following the operating instructions for your component. Set the input mode to AUTO. There is noise interference when a subwoofer is not connected to this unit. The protection circuitry was in operation because a source with strong bass elements was played back. Turn down the volume level. Select SWFR for BASS OUT. Connect a subwoofer and adjust settings for SUBWOOFER SET. Low frequency sounds are distorted. CROSS OVER in SUBWOOFER SET is Set CROSS OVER correctly. set incorrectly. On-screen display does not appear. The OSD video pin cable is not connected properly. Connect the cable properly. TV is not selected as the input source. Select TV as the input source. No picture is displayed for external components, such as a DVD player. The video cable is not connected properly. TV is not selected as the input source. Connect the cable properly. Select TV as the input source. This unit does not operate properly. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Disconnect the AC power cable from the outlet and then plug it in again after about 30 seconds. There is noise interference from digital or high-frequency equipment. This unit is too close to the digital or high-frequency equipment. Move this unit further away from such equipment. This unit does not output effect sounds properly. The original source includes surround effects. Disable surround effect settings on this unit. See page - - - 81 38 70 70 70 15 37 15 37 - - - 88

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
88
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
Surround sound effects are
insubstantial.
The listening room is not a regular shape.
Install this unit in a square or rectangular
shaped room.
—
There is no wall in the path of the sound
beam.
Try placing a flat object, such as a board,
in the path of the sound beam.
—
Dolby Digital or DTS sources
cannot be played. (Dolby Digital or
DTS indicator does not light up in
the front panel display.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following
the operating instructions for your
component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO.
81
There is noise interference when a
subwoofer is not connected to this
unit.
The protection circuitry was in operation
because a source with strong bass
elements was played back.
Turn down the volume level.
38
Select SWFR for BASS OUT.
70
Connect a subwoofer and adjust settings
for SUBWOOFER SET.
70
Low frequency sounds are
distorted.
CROSS OVER in SUBWOOFER SET is
set incorrectly.
Set CROSS OVER correctly.
70
On-screen display does not
appear.
The OSD video pin cable is not
connected properly.
Connect the cable properly.
15
TV is not selected as the input source.
Select TV as the input source.
37
No picture is displayed for
external components, such as a
DVD player.
The video cable is not connected
properly.
Connect the cable properly.
15
TV is not selected as the input source.
Select TV as the input source.
37
This unit does not operate
properly.
The internal microcomputer has been
frozen by an external electric shock
(such as lightning or excessive static
electricity) or by a power supply with
low voltage.
Disconnect the AC power cable from the
outlet and then plug it in again after
about 30 seconds.
—
There is noise interference from
digital or high-frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such
equipment.
—
This unit does not output effect
sounds properly.
The original source includes surround
effects.
Disable surround effect settings on this
unit.
—