Asus P I-P55TP4N User Manual - Page 50

Save and Exit Setup, Exit Without Saving

Get Asus P I-P55TP4N PDF manuals and user guides View all Asus P I-P55TP4N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

IV. BIOS SOFTWARE If you are auto-detecting a hard disk that supports the LBA mode, three lines will appear in the parameter box. Choose the line that lists LBA for an LBA drive. Do not select Large or Normal. The auto-detection feature can only detect one set of parameters for a particular IDE hard drive. Some IDE drives can use more than one set. This is not a problem if the drive is new and there is nothing on it. However, if the drive is already formatted when you install it and different parameters than those detected were used, you will need to enter them manually yourself. If the parameters listed differ from the ones used when the drive was formatted, the drive will not be readable. If the auto-detected parameters do not match the ones that should be used for your drive, do not accept them. Press the key to reject the presented settings and enter the correct ones manually from the Standard CMOS Setup screen. Save and Exit Setup Select this option to save into the CMOS memory all modifications you specify during the current session. To save the configuration changes, highlight the "Save & Exit Setup" option on the main screen and then press the key. IV. BIOS (Load Setup Defaults) IV. BIOS (Save & Exit) Exit Without Saving Select this option to exit the Setup utility without saving the modifications you specify during the current session. To exit without saving, highlight the "Exit Without Saving" option on the main screen and then press the key. 44 P/I-P55TP4N User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
P/I-P55TP4N User's Manual
44
If you are auto-detecting a hard disk that supports the LBA mode, three
lines will appear in the parameter box.
Choose the line that lists LBA for an
LBA drive.
Do not select Large or Normal.
The auto-detection feature can only detect one set of parameters for a par-
ticular IDE hard drive.
Some IDE drives can use more than one set.
This is
not a problem if the drive is new and there is nothing on it.
However, if the
drive is already formatted when you install it and different parameters than
those detected were used, you will need to enter them manually yourself.
If the parameters listed differ from the ones used when the drive was for-
matted, the drive will not be readable.
If the auto-detected parameters do
not match the ones that should be used for your drive, do not accept them.
Press the <N> key to reject the presented settings and enter the correct ones
manually from the Standard CMOS Setup screen.
Save and Exit Setup
Select this option to save into the CMOS memory all modifications you
specify during the current session.
To save the configuration changes, high-
light the “Save & Exit Setup” option on the main screen and then press the
<Enter> key.
Exit Without Saving
Select this option to exit the Setup utility without saving the modifications
you specify during the current session.
To exit without saving, highlight the
“Exit Without Saving” option on the main screen and then press the <En-
ter> key.
IV.
BIOS SOFTWARE
IV.
BIOS
(Load Setup Defaults)
IV.
BIOS
(Save & Exit)