Brother International BAS-343E Instruction Manual - English - Page 44

Changing the presser foot lift

Page 44 highlights

9-8. Changing the presser foot lift ˙ Standard presser foot q lift is 3 mm (max. 8 mm). 9. Standard adjutsments 3 5 mm 0.5 1 mm Adjusting presser foot lift to 3 - 5mm 1. Loosen the stud screw w and open the intermittent cover e. 2. Loosen the nut r and adjust the intermittent presser connecting rod t pisition. (When the intermittent presser connecting rod is raised, the lift will increase. When lowered, the lift will Adjusting presser foot lift to 5 - 8 mm 1. Turn the upper shaft to set the presser foot to its lowest point. Loosen the screw o of intermittent presser arm (R) i. Adjust the clearance between the presser lifter y and the presser bar bush u to 0.5 - 1 mm. 2. Loosen the nut r and adjust the intermittent presser connecting rod t position. (When the intermittent presser connecting rod is raised, the lift will increase. When lowered, the lift will 3. Loosen the presser foot screw and adjust the height of the presser foot so that it is 0.5 mm above the top of the material being sewn when the presser foot is lowered. If vertical movement of the presser foot is not required 1. Remove the face plate !0. 2. Remove the stud screw !1 and re-attach the intermitte connecting rod !2 to the upper screw hole !4 of the intermit- tent presser arm R !.3 BAS-343E 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66

9.
Standard adjutsments
37
BAS-343E
9-8. Changing the presser foot lift
Standard presser foot
q
lift is 3 mm (max. 8 mm).
Adjusting presser foot lift to 3 - 5mm
1.
Loosen the stud screw
w
and open the intermittent cover
e
.
2.
Loosen the nut
r
and adjust the intermittent presser connecting rod
t
pisition.
(When the intermittent presser connecting rod is raised, the lift will increase.
When lowered, the lift will
Adjusting presser foot lift to 5 - 8 mm
1.
Turn the upper shaft to set the presser foot to its lowest point.
Loosen the screw
o
of intermittent presser arm (R)
i
.
Adjust the clearance between the presser lifter
y
and the presser bar bush
u
to 0.5 - 1 mm.
2.
Loosen the nut r and adjust the intermittent presser connecting rod
t
position.
(When the intermittent presser connecting rod is raised, the lift will increase.
When lowered, the lift will
3.
Loosen the presser foot screw and adjust the height of the presser foot so that it is 0.5 mm above the top of the
material being sewn when the presser foot is lowered.
If vertical movement of the presser foot is not required
1.
Remove the face plate
!0
.
2.
Remove the stud screw
!
1
and re-attach the intermitte connecting rod
!
2
to the upper screw hole
!
4
of the intermit-
tent presser arm R
!3
.
0.5
-
1 mm
3
-
5 mm