Brother International Innov-ís 40 Users Manual - English - Page 98

Error messages

Get Brother International Innov-ís 40 PDF manuals and user guides View all Brother International Innov-ís 40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Error messages If the sewing machine is incorrectly operated or if the sewing machine malfunctions, an error message appears in the LCD. The message can be cleared by pressing any key in the operation panel, turning any dial, or performing the operation correctly. Error Message (in LCD) Probable Cause Remedy The start/stop button or the reverse/reinforcement stitch button was pressed (The foot controller was depressed if it is connected.) while the presser foot is raised. Lower the presser foot before continuing the operation. A stitch other than the buttonhole or bar tack stitch was selected and the start/stop button was pressed (The foot controller was depressed if it is connected.) while the buttonhole lever is lowered. Raise the buttonhole lever before continuing the operation. The buttonhole or bar tack stitch was selected and the start/stop button was pressed (The foot controller was depressed if it is connected.) while the buttonhole lever is raised. The reverse/reinforcement stitch button or needle Lower the buttonhole lever before continuing the operation. Move the bobbin winder 4 position button was pressed while the bobbin winder shaft to the left before con- shaft is moved to the right. tinuing the operation. The start/stop button was pressed, even though the foot controller is connected. The motor locked up because the thread is tangled. The needle mode selection key was pressed to select twin needle sewing while a stitch that cannot be used with the twin needle is selected. The pattern selection dial was turned to select a pattern while the twin needle setting is selected. Disconnect the foot controller, and then press the start/stop button. Otherwise, operate the machine by using the foot controller. Turn off the machine and remove the tangled thread before continuing the operation. Select a stitch that can be used with the twin needle. Cancel the twin needle setting, and then select a stitch. Memo ● If error message "F1" through "F9" appears in the LCD while the sewing machine is being used, the machine may be malfunctioning. Contact your dealer or the nearest authorized service center. 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
97
4
Error messages
If the sewing machine is incorrectly operated or if the sewing machine malfunctions, an error message appears
in the LCD.
The message can be cleared by pressing any key in the operation panel, turning any dial, or performing the
operation correctly.
Memo
●
If error message “F1” through “F9” appears in the LCD while the sewing machine is being used, the
machine may be malfunctioning. Contact your dealer or the nearest authorized service center.
Error Message
(in LCD)
Probable Cause
Remedy
The start/stop button or the reverse/reinforcement
stitch button was pressed (The foot controller was
depressed if it is connected.) while the presser foot is
raised.
Lower the presser foot
before continuing the opera-
tion.
A stitch other than the buttonhole or bar tack stitch
was selected and the start/stop button was pressed
(The foot controller was depressed if it is connected.)
while the buttonhole lever is lowered.
Raise the buttonhole lever
before continuing the opera-
tion.
The buttonhole or bar tack stitch was selected and
the start/stop button was pressed (The foot controller
was depressed if it is connected.) while the button-
hole lever is raised.
Lower the buttonhole lever
before continuing the opera-
tion.
The reverse/reinforcement stitch button or needle
position button was pressed while the bobbin winder
shaft is moved to the right.
Move the bobbin winder
shaft to the left before con-
tinuing the operation.
The start/stop button was pressed, even though the
foot controller is connected.
Disconnect the foot
controller, and then press the
start/stop button. Otherwise,
operate the machine by
using the foot controller.
The motor locked up because the thread is tangled.
Turn off the machine and
remove the tangled thread
before continuing the opera-
tion.
The needle mode selection key was pressed to select
twin needle sewing while a stitch that cannot be
used with the twin needle is selected.
Select a stitch that can be
used with the twin needle.
The pattern selection dial was turned to select a pat-
tern while the twin needle setting is selected.
Cancel the twin needle set-
ting, and then select a stitch.