Brother International Quattro 2 6700D Users Manual - English - Page 348
Main power switch is not turned on. - foot book
View all Brother International Quattro 2 6700D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 348 highlights
TROUBLESHOOTING Problem Embroidery pattern does not sew out correctly Loops appear on the surface of the fabric when embroidering Machine does not operate Embroidery unit does not operate Nothing happens, even if the LCD display is pressed Cause Solution Thread is twisted. Use scissors, etc., to cut the twisted thread and remove it from the race, etc. Fabric was not inserted into the frame correctly (fabric was loose, etc.). If the fabric is not stretched tight in the frame, the pattern may turn out poorly or there may be shrinkage of the pattern. Set the fabric into the frame correctly. Stabilizing material was not attached. Always use stabilizing material, especially with stretch fabrics, lightweight fabrics, fabrics with a coarse weave, or fabrics that often cause pattern shrinkage. See your authorized dealer for the proper stabilizer. There was an object placed near the machine, and the carriage or embroidery frame hit the object during sewing. If the frame bumps something during sewing, the pattern will turn out poorly. Do not place anything in the area where the frame may bump it during sewing. Fabric outside the frame edges interferes with Reinsert the fabric in the embroidery frame so the sewing arm, so the embroidery unit cannot that the excess fabric is away from the sewing move. arm, and rotate the pattern 180 degrees. Fabric is too heavy, so the embroidery unit cannot move freely. Place a large thick book or similar object under the arm head to lightly lift the heavy side and keep it level. Fabric is hanging off the table. If the fabric is hanging off the table during embroidery, the embroidery unit will not move freely. Place the fabric so that it does not hang off the table or hold the fabric to keep it from dragging. Fabric is snagged or caught on something. Stop the machine and place the fabric so that it does not get caught or snagged. Embroidery frame was removed during sewing (for example, to reset the bobbin). The presser foot was bumped or moved while removing or attaching the embroidery frame, or the embroidery unit was moved. If the presser foot is bumped or the embroidery unit is moved during sewing, the pattern will not turn out. Be careful when removing or reattaching the embroidery frame during sewing. Stabilizer is incorrectly attached, for example, it Attach the stabilizer correctly. is smaller than the embroidery frame. The thread tension is incorrectly set. Adjust the thread tension. The tension of the upper thread is incorrectly set Use the embroidery needle plate cover. for the combination of the fabric, thread and pattern being used. The combination of the bobbin case and bobbin Change the bobbin case or bobbin thread so thread is incorrect. that the correct combination is used. There is no pattern selected. Select a pattern. "Start/Stop" button was not pushed. Press the "Start/Stop" button. Main power switch is not turned on. Turn the main power to ON. Presser foot is not lowered. Lower the presser foot. "Start/Stop" button was pushed with the foot controller attached. Remove the foot controller, or use the foot controller to operate the machine. The "Start/Stop" button was pressed while the Use the foot controller instead of the "Start/ machine is set for the sewing speed controller to Stop" button to operate the machine, or set control the zigzag stitch width. the Width control to OFF in the Sewing settings. All keys and buttons have been locked by . Press buttons. to unlock all keys and There is no pattern selected. Select a pattern. Main power switch is not turned on. Turn the main power to ON. Embroidery unit is not attached correctly. Reattach the embroidery unit correctly. Embroidery frame was attached before the unit Perform the initialization process correctly. was initialized. The screen has been locked. Press either of the following keys to unlock the screen. The fabric feeds in the The feed mechanism is damaged. opposite direction. The LCD screen is fogged up. Condensation has formed on the LCD screen. Contact your dealer or the nearest authorized service center. After a while, the cloudiness will disappear. Page - 203 200 218 203 - 218 - 229 200 233 - 235 219 218 91, 156, 190, 265 15 26 15 73 35, 73 65, 67 190, 265 26 188 188 - - - 346