Brother International T-8752C Instruction Manual - English - Page 30

Installing the bobbin, PREPARATION BEFORE SEWING, <Latch type&gt

Get Brother International T-8752C PDF manuals and user guides View all Brother International T-8752C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

4. PREPARATION BEFORE SEWING 4-4. Installing the bobbin CAUTION Turn off the power switch before installing the bobbin. The machine may operate if the treadle is depressed by mistake, which could result in injury. 2898M 1. Insert the bobbin (1) into the rotary hook (2) so that the winding direction is as shown in the illustration. 2. Return the rotary hook latch (3) to its original position. 3. Turn the machine pulley to rotate the rotary hook (2) until the tension spring (4) is visible. 4. Pass the thread through slit (5) in the rotary hook and then pass it under the thread tension spring. 5. Pull out the thread to a length of approximately 50 mm. 6. Close the slide plates. 2465B 2900M There is an anti-spin spring (6) inside the rotary hook. The anti-spin spring (6) prevents the bobbin from racing at times such as during thread trimming. Use bobbins (1) made of light alloy as specified by BROTHER. 2466B 21 T-8421C, 8422C, 8452C, 8722C, 8752C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
T-8421C, 8422C, 8452C, 8722C, 8752C
4. PREPARATION BEFORE SEWING
21
4-4. Installing the bobbin
CAUTION
Turn off the power switch before installing the bobbin.
The machine may operate if the treadle is depressed by mistake, which could result in injury.
<Latch type>
1. Insert the bobbin (1) into the rotary hook (2) so that the
winding direction is as shown in the illustration.
2. Return the rotary hook latch (3) to its original position.
3. Turn the machine pulley to rotate the rotary hook (2) until
the tension spring (4) is visible.
4. Pass the thread through slit (5) in the rotary hook and then
pass it under the thread tension spring.
5. Pull out the thread to a length of approximately 50 mm.
6. Close the slide plates.
±
There is an anti-spin spring (6) inside the rotary hook. The
anti-spin spring (6) prevents the bobbin from racing at times
such as during thread trimming.
±
Use bobbins (1) made of light alloy as specified by
BROTHER.
2898M
2465B
2900M
2466B