Brother International T-8752C Instruction Manual - English - Page 77

Clearance between rotary hook and opener, 13-6. Presser foot height

Get Brother International T-8752C PDF manuals and user guides View all Brother International T-8752C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

13. STANDARD ADJUSTMENT 13-5. Clearance between rotary hook and opener 1. Loosen the set screw (3) and move the opener (1) to the left or right to adjust so that the clearance between the rotary hook (2) and the opener (1) is 0.1-0.3 mm when the opener (1) is pulled as far as it will go in the direction of the arrow. 2. Tighten the set screw (3). NOTE: If the clearance is too large • Upper thread trimming errors may occur (models with thread trimmer). • The right upper thread may be cut too short (models with thread trimmer). If the clearance is too small • The rotary hook may become damaged. • The opener (1) may become damaged. 13-6. Presser foot height 2477B 2206B 1. Remove the rear cover (1) and remove the rubber cap (2). 2. Loosen the nut (3) and loosen the presser adjusting screw (4). 3. Use the lifting lever (5) to raise the presser foot (6). 4. Loosen the screw (7) and move the presser bar (8) up or down to adjust so that the presser foot (6) is approximately 7 mm above the top of the needle plate. NOTE: Do not turn the presser bar (8) at this time. 5. Tighten the screw (7). 6. Turn the presser adjusting screw (4) to adjust the presser foot pressure, and then tighten the nut (3). Approx. 7mm 3059M T-8421C, 8422C, 8452C, 8722C, 8752C 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
T-8421C, 8422C, 8452C, 8722C, 8752C
13. STANDARD ADJUSTMENT
68
13-5. Clearance between rotary hook and opener
1. Loosen the set screw (3) and move the opener (1) to the
left or right to adjust so that the clearance between the
rotary hook (2) and the opener (1) is 0.1–0.3 mm when
the opener (1) is pulled as far as it will go in the direction
of the arrow.
2. Tighten the set screw (3).
NOTE
:
If the clearance is too large
• Upper thread trimming errors may occur (models with
thread trimmer).
• The right upper thread may be cut too short (models with
thread trimmer).
If the clearance is too small
• The rotary hook may become damaged.
• The opener (1) may become damaged.
13-6. Presser foot height
1. Remove the rear cover (1) and remove the rubber cap (2).
2. Loosen the nut (3) and loosen the presser adjusting screw
(4).
3. Use the lifting lever (5) to raise the presser foot (6).
4. Loosen the screw (7) and move the presser bar (8) up or
down to adjust so that the presser foot (6) is
approximately 7 mm above the top of the needle plate.
NOTE
:
Do not turn the presser bar (8) at this time.
5. Tighten the screw (7).
6. Turn the presser adjusting screw (4) to adjust the presser
foot pressure, and then tighten the nut (3).
2477B
2206B
3059M
Approx. 7mm