Cisco SFS-7012 User Guide - Page 50

Enter, Spacebar, boot], image1, reboot

Get Cisco SFS-7012 - SFS InfiniBand Server Switch 7012 PDF manuals and user guides View all Cisco SFS-7012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter Step 1 Step 2 Step 3 Step 4 Step 5 Ensure that the spine module is connected to a COM port on a serial terminal device via the RS-232 port. Get to a [boot]: prompt by following Step a or b. a. If the managed spine is running, enter the following command at the console: reboot Then press Enter. b. If the managed spine is not running, power on the switch. After selecting image1 or image2, press the Spacebar to interrupt the auto load sequence before the counter expires (within 5 seconds). At the [boot]: prompt enter the new spine IP address with the following syntax: spineip Then press Enter. At the [boot]: prompt, enter reboot, and press Enter. Upon reboot the managed spine will display information similar to the following: Unified Boot Manager For The T3 Platform. Image Date: Jan 19 2006, 15:03:31 Checking L2 functionality... BCM1125 L2 caches initialized and invalidated CPU0 caches initialized Initialized SMBUS Channels SPD Checksum ok. MEM_SEL = 0x00000007 CPU_REV = 0x00000001_112421FF CPU speed = 400 MHz IO Bridge 0,1 speed = 133, 200 MHz Memory size = 128 MB MC1 Configured for 128M SODIMM, CAS=2, 100 MHz Configured Memory Size = 0x08000000 Channel Interleave Bit = 0 Number of Mem Channels = 1 Testing memory Memory tests pass CPU0 flushing caches L2 flush complete Start type = 0xBFC006A0 Jumping to romStart Initializing HyperTransport bus HyperTransport initialization completed rintf MBOX connect interrupt_source=28 vector=62 status=0 Printf MBOX intEnable status=0 Found Intel Strata Flash 128 MBit (0x8918). Mounted raw file system on device /image1. (size=6291456 bytes) Mounted raw file system on device /image2. (size=6291456 bytes) Mounted raw file system on device /dump0. (size=1048576 bytes) Mounted flash file system on device /rfa1. (size=2097152 bytes) Unified Boot Manager [1] image1 [2] image2 CPU: Broadcom BCM1125 VxWorks Version: 5.4 [boot]: Unified Boot Manager For The T3 Platform. Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide 32 OL-8787-04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
32
Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide
OL-8787-04
Chapter
Step 1
Ensure that the spine module is connected to a COM port on a serial terminal device via the RS-232 port.
Step 2
Get to a
[boot]:
prompt by following Step a or b.
a.
If the managed spine is running, enter the following command at the console:
reboot
Then press
Enter
.
b.
If the managed spine is not running, power on the switch.
Step 3
After selecting
image1
or
image2
, press the
Spacebar
to interrupt the auto load sequence before the
counter expires (within 5 seconds).
Step 4
At the
[boot]:
prompt enter the new spine IP address with the following syntax:
spineip <NEW IP ADDRESS>
Then press
Enter
.
Step 5
At the
[boot]:
prompt, enter
reboot
, and press
Enter
. Upon reboot the managed spine will display
information similar to the following:
Unified Boot Manager For The T3 Platform.
Image Date:
Jan 19 2006, 15:03:31
Checking L2 functionality...
BCM1125
L2 caches initialized and invalidated
CPU0 caches initialized
Initialized SMBUS Channels
SPD Checksum ok.
MEM_SEL = 0x00000007
CPU_REV = 0x00000001_112421FF
CPU speed = 400 MHz
IO Bridge 0,1 speed = 133, 200 MHz
Memory size = 128 MB
MC1 Configured for 128M SODIMM, CAS=2, 100 MHz
Configured Memory Size = 0x08000000
Channel Interleave Bit = 0
Number of Mem Channels = 1
Testing memory
Memory tests pass
CPU0 flushing caches
L2 flush complete
Start type = 0xBFC006A0
Jumping to romStart
Initializing HyperTransport bus
HyperTransport initialization completed
rintf MBOX connect interrupt_source=28 vector=62 status=0
Printf MBOX intEnable status=0
Found Intel Strata Flash 128 MBit (0x8918).
Mounted raw file system on device /image1. (size=6291456 bytes)
Mounted raw file system on device /image2. (size=6291456 bytes)
Mounted raw file system on device /dump0. (size=1048576 bytes)
Mounted flash file system on device /rfa1. (size=2097152 bytes)
Unified Boot Manager
[1] image1
[2] image2
CPU: Broadcom BCM1125
VxWorks Version: 5.4
[boot]:
Unified Boot Manager For The T3 Platform.