Compaq ProLiant 1850R Compaq ProLiant 1850R Setup and Installation Guide - Page 176

NIC Operating Mode, SCSI Device Jumper Settings, Table E-3

Get Compaq ProLiant 1850R PDF manuals and user guides View all Compaq ProLiant 1850R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 176 highlights

E-4 Switches and Jumpers NIC Operating Mode The ProLiant 1850R server comes standard with the Compaq Netelligent 10/100 TX embedded controller. The controller automatically differentiates between the 10Mb and 100Mb environments when the RJ-45 connector is used. SCSI Device Jumper Settings No two SCSI devices connected to the same SCSI controller can have the same SCSI ID. If another SCSI device is connected to the same controller, check its SCSI ID in the Compaq System Configuration Utility before beginning the installation procedure for this additional drive. The SCSI ID is set by jumpers ID 2, ID 1, and ID 0 located on each SCSI device. The following chart provides the SCSI ID jumper settings for Compaq SCSI hard drives. Table E-3 SCSI Device Jumper ID Settings SCSI ID 6 5 4 3 2 1 0 Bit 2 Bit 1 Bit 0 ON ON OFF ON OFF ON ON OFF OFF OFF ON ON OFF ON OFF OFF OFF ON OFF OFF OFF

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
E-4
Switches and Jumpers
NIC Operating Mode
The ProLiant 1850R server comes standard with the Compaq Netelligent 10/100
TX embedded controller. The controller automatically differentiates between
the 10Mb and 100Mb environments when the RJ-45 connector is used.
SCSI Device Jumper Settings
No two SCSI devices connected to the same SCSI controller can have the same
SCSI ID. If another SCSI device is connected to the same controller, check its
SCSI ID in the Compaq System Configuration Utility before beginning the
installation procedure for this additional drive. The SCSI ID is set by jumpers
ID 2, ID 1, and ID 0 located on each SCSI device.
The following chart provides the SCSI ID jumper settings for Compaq SCSI
hard drives.
Table E-3
SCSI Device Jumper ID Settings
SCSI ID
Bit 2
Bit 1
Bit 0
6
ON
ON
OFF
5
ON
OFF
ON
4
ON
OFF
OFF
3
OFF
ON
ON
2
OFF
ON
OFF
1
OFF
OFF
ON
0
OFF
OFF
OFF