Compaq ProLiant 1850R Compaq ProLiant 1850R Setup and Installation Guide - Page 96

Installing the 1.44-MB Diskette Drive (Floppy Drive), Enabling the Power Switch Security Feature

Get Compaq ProLiant 1850R PDF manuals and user guides View all Compaq ProLiant 1850R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

3-21 Installing the 1.44-MB Diskette Drive (Floppy Drive) To install the 1.44-MB diskette drive into the server, reverse the steps noted in the proceeding procedure. Enabling the Power Switch Security Feature When the power switch security feature is enabled it protects the server from being shut down due to unintentional contact with the power switch. In the enabled mode you must use a slender rod (such as the eraser end of a pencil) to depress the center circle of the power switch. To enable the power switch security feature: 1. Power OFF the server and remove power cord (s). IMPORTANT: The system power in the ProLiant 1850R server does not completely shut off with the front panel Power On/Standby switch. The two positions of the switch functions as ON and STANDBY, rather than ON and OFF. The STANDBY position removes power from most of the electronics and the drives but portions of the power supply and some internal circuitry remain active. Consequently, to completely remove all power from the system, you must disconnect the power cord from the server. In systems with multiple power supplies, you must disconnect all the power cords to completely remove power from the system. 2. Remove the server cover. See Chapter 3, "Installing Hardware Options" for details. 3. Remove the 1.44-MB diskette drive. 4. Use a narrow instrument to release each clip from the bezel – and — by pushing inward slightly. 5. Once each clip is disengaged, remove the switch parts from the bezel, collecting the two plastic parts and the spring as they disengage from the bezel. Tension in the spring may cause it to come loose, so be careful with the spring. Compaq ProLiant 1850R Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
3-21
Compaq ProLiant 1850R Setup and Installation Guide
Installing the 1.44-MB Diskette Drive
(Floppy Drive)
To install the 1.44-MB diskette drive into the server, reverse the steps noted in
the proceeding
procedure.
Enabling the Power Switch Security Feature
When the power switch security feature is enabled it protects the server from
being shut down due to unintentional contact with the power switch.
In the
enabled mode you must use a slender rod (such as the eraser end of a pencil)
to depress the center circle of the power switch.
To enable the power switch security feature:
1.
Power OFF the server and remove power cord (s).
IMPORTANT:
The system power in the ProLiant 1850R server does not
completely shut off with the front panel Power On/Standby switch.
The two
positions of the switch functions as ON and STANDBY, rather than ON and
OFF.
The STANDBY position removes power from most of the electronics and
the drives but portions of the power supply and some internal circuitry remain
active.
Consequently, to completely remove all power from the system, you
must disconnect the power cord from the server.
In systems with multiple
power supplies, you must disconnect
all
the power cords to completely
remove power from the system.
2.
Remove the server cover. See Chapter 3,
“
Installing Hardware Options
”
for details.
3.
Remove the 1.44-MB diskette drive.
4.
Use a narrow instrument to release each clip from the bezel
➊
and
➋
by
pushing inward slightly.
5.
Once each clip is disengaged, remove the switch parts from the bezel,
collecting the two plastic parts and the spring as they disengage from the
bezel.
Tension in the spring may cause it to come loose, so be careful
with the spring.