Compaq ProLiant 1850R Compaq ProLiant 1850R Setup and Installation Guide - Page 63

Attaching Server Rails to the Server

Get Compaq ProLiant 1850R PDF manuals and user guides View all Compaq ProLiant 1850R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

2-25 Attaching Server Rails to the Server 1. Place the center tab on the server rail with the open end of the tab towards the front of the server. IMPORTANT: The server rails attach to the server with the flat side of the rail towards the server. The holes in the server rail will line up only one way with the chassis. 2. Attach the flat side of a component rail to each side of the server chassis with three 8-32 x 1/4-inch Phillips screws. Do not use washers with the screws. Figure 2-16. Attaching server rails to the server Attaching the Server Bracket to the Server The server bracket fastens to the left side of the rear of the server chassis. The server bracket provides an attachment point for the cable management arm from the server to the rear frame of the rack. Attach the server bracket to the back of the server with two 6-32 x 1/4 Phillips screws. Compaq ProLiant 1850R Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
2-25
Compaq ProLiant 1850R Setup and Installation Guide
Attaching Server Rails to the Server
1.
Place the center tab on the server rail with the open end of the tab
towards the front of the server.
IMPORTANT:
The server rails attach to the server with the flat side of the rail
towards the server. The holes in the server rail will line up only one way with
the chassis.
2.
Attach the flat side of a component rail to each side of the server chassis with
three 8-32 x 1/4-inch Phillips screws. Do not use washers with the screws.
Figure 2-16. Attaching server rails to the server
Attaching the Server Bracket to the
Server
The server bracket fastens to the left side of the rear of the server chassis. The
server bracket provides an attachment point for the cable management arm from
the server to the rear frame of the rack.
Attach the server bracket to the back of the server with two 6-32 x 1/4 Phillips
screws.