Compaq ProLiant 1850R Compaq ProLiant 1850R Setup and Installation Guide - Page 52

Attaching the Outer Bracket Rail to the Rack Mounting Bracket, IMPORTANT

Get Compaq ProLiant 1850R PDF manuals and user guides View all Compaq ProLiant 1850R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

2-14 Server Installation Overview IMPORTANT: To make installing the rack mounting bracket easier, attach the outer bracket rail to the rack mounting bracket before attaching the rack mounting bracket assembly to the rack. This way, the joined mounting bracket and bracket rail can be fastened to the rack as one assembly. Attaching the Outer Bracket Rail to the Rack Mounting Bracket 1. Lay the slide rail assemblies (2), rack mounting brackets (2) and 1/4-inch fasteners (4) on a flat surface. 2. Extend the server rail from the outer bracket rail until the server rail release latch clicks Œ. Holding down the latch , slip the server rail out of the inner slide Ž, as shown in the following figure. 1 Reverse Angle 2 3 Figure 2-5. Removing server rail from outer bracket rail 3. Repeat for the second slide rail assembly. 4. Set the server rails to one side. You will attach them to the rack server chassis later, as discussed in the section, "Attaching Server Rails to the Server." Build two mirror image assemblies of the following assembly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
2-14
Server Installation Overview
IMPORTANT:
To make installing the rack mounting bracket easier, attach the
outer bracket rail to the rack mounting bracket before attaching the rack
mounting bracket assembly to the rack. This way, the joined mounting
bracket and bracket rail can be fastened to the rack as one assembly.
Attaching the Outer Bracket Rail
to the Rack Mounting Bracket
1.
Lay the slide rail assemblies (2), rack mounting brackets (2) and
1/4-inch fasteners (4) on a flat surface.
2.
Extend the server rail from the outer bracket rail until the server rail
release latch clicks
±
. Holding down the latch
²
, slip the server rail out
of the inner slide
³
, as shown in the following figure.
1
3
2
Reverse
Angle
Figure 2-5. Removing server rail from outer bracket rail
3.
Repeat for the second slide rail assembly.
4.
Set the server rails to one side. You will attach them to the rack server
chassis later,
as discussed in the section, "Attaching Server Rails to the
Server."
Build two mirror image assemblies of the following assembly.