Compaq ProLiant 1850R Compaq ProLiant 1850R Setup and Installation Guide - Page 98

Replacing the CD-ROM Drive

Get Compaq ProLiant 1850R PDF manuals and user guides View all Compaq ProLiant 1850R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

3-23 Replacing the CD-ROM Drive The following procedure discusses removing and installing the CD-ROM drive. Removing the CD-ROM Drive 1. If the server is on, place it in Standby and disconnect the power cord-(s). See to Chapter 2, "Server Installation Overview". 2. Pull the server forward in the rack for access to the inside of the server. 3. Remove the server cover. 4. Remove the 1.44-MB diskette drive (floppy drive) to access the screw which secures the CD-ROM drive. See proceeding procedure for details. 5. Remove the screw that secures the CD-ROM tray assembly to the chassis. Slide the CD-ROM tray forward out of the server. The CD-ROM tray and the CD-ROM drive adapter board disconnect. CD-ROM cabling remains attached to the CD-ROM adapter board. Figure 3-24. Removing the CD-ROM drive from the chassis Installing the CD-ROM Drive To install the CD-ROM drive into the server, reverse the steps noted in the proceeding procedure. Below is an example of installing the CD-ROM. Compaq ProLiant 1850R Setup and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
3-23
Compaq ProLiant 1850R Setup and Installation Guide
Replacing the CD-ROM Drive
The following procedure discusses removing and installing the CD-ROM drive.
Removing the CD-ROM Drive
1.
If the server is on, place it in Standby and disconnect the power cord-(s).
See to Chapter 2,
“
Server Installation Overview
”
.
2.
Pull the server forward in the rack for access to the inside of the server.
3.
Remove the server cover.
4.
Remove the 1.44-MB diskette drive (floppy drive) to access the screw
which secures the CD-ROM drive. See proceeding procedure for details.
5.
Remove the screw that secures the CD-ROM tray assembly to the chassis.
Slide the CD-ROM tray forward out of the server. The
CD-ROM tray and the CD-ROM drive adapter board disconnect.
CD-ROM cabling remains attached to the CD-ROM adapter board.
Figure 3-24.
Removing the CD-ROM drive from the chassis
Installing the CD-ROM Drive
To install the CD-ROM drive into the server, reverse the steps noted in the
proceeding
procedure. Below is an example of installing the CD-ROM.