Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 12

Removal and Replacement Procedures, Electrostatic Discharge Information

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

2-1 Chapter 2 Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for Compaq ProLiant 800 Servers. After completing all necessary removal and replacement procedures, run the Diagnostics program to verify that all components operate properly. To service Compaq ProLiant 800 Servers, you might need the following: I Torx T-15 screwdriver I From the Compaq SmartStart and Support Software CD: ❏ System Configuration Utility software ❏ Drive Array Advanced Diagnostics software ❏ Diagnostics software Electrostatic Discharge Information A discharge of static electricity can damage static-sensitive devices or microcircuitry. Proper packaging and grounding techniques are necessary precautions to prevent damage. To prevent electrostatic damage, observe the following precautions: I Transport products in static-safe containers such as conductive tubes, bags, or boxes. I Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations. I Cover work stations with approved static-dissipating material. Provide a wrist strap connected to the work surface and properly grounded tools and equipment. I Keep work area free of non-conductive materials such as ordinary plastic assembly aids and foam packing. I Make sure you are always properly grounded when touching a static-sensitive component or assembly. I Avoid touching pins, leads, or circuitry. I Always place drives PCB assembly side down. I Use conductive field service tools. Compaq ProLiant 800 Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-1
Compaq ProLiant 800 Servers Maintenance and Service Guide
Chapter 2
Removal and Replacement Procedures
This chapter provides subassembly/module-level removal and replacement procedures for
Compaq ProLiant 800 Servers. After completing all necessary removal and replacement
procedures, run the Diagnostics program to verify that all components operate properly.
To service Compaq ProLiant 800 Servers, you might need the following:
■
Torx T-15 screwdriver
■
From the Compaq SmartStart and Support Software CD:
❏
System Configuration Utility software
❏
Drive Array Advanced Diagnostics software
❏
Diagnostics software
Electrostatic Discharge Information
A discharge of static electricity can damage static-sensitive devices or microcircuitry. Proper
packaging and grounding techniques are necessary precautions to prevent damage. To prevent
electrostatic damage, observe the following precautions:
■
Transport products in static-safe containers such as conductive tubes, bags, or boxes.
■
Keep electrostatic-sensitive parts in their containers until they arrive at
static-free stations.
■
Cover work stations with approved static-dissipating material. Provide a wrist strap
connected to the work surface and properly grounded tools and equipment.
■
Keep work area free of non-conductive materials such as ordinary plastic assembly aids
and foam packing.
■
Make sure you are always properly grounded when touching a static-sensitive component
or assembly.
■
Avoid touching pins, leads, or circuitry.
■
Always place drives PCB assembly side down.
■
Use conductive field service tools.