Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 30

Power Switch and Cable Assembly

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2-19 Power Switch and Cable Assembly The power switch and cable assembly is removed for replacement only. To remove the power switch and cable assembly: WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards. The enclosed area contains no operator-serviceable parts. To reduce the risk of injury from electrical shock hazards, do not open this enclosure. 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top cover. See "Top Cover" earlier in this chapter. 3. Disconnect all cables from the power switch and cable assembly. 4. Remove the single T-15 screw that secures the power switch and cable assembly to the  chassis .   5. Slide the power switch back , then lift it out of the chassis . 2 3 1 Figure 2-17. Removing the power switch and cable assembly Reverse steps 1 through 5 to replace the power switch and cable assembly. Compaq ProLiant 800 Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-19
Compaq ProLiant 800 Servers Maintenance and Service Guide
Power Switch and Cable Assembly
The power switch and cable assembly is removed for replacement only.
To remove the power switch and cable assembly:
WARNING
:
Any surface or area of the equipment marked with these symbols
indicates the presence of electrical shock hazards. The enclosed area contains no
operator-serviceable parts. To reduce the risk of injury from electrical shock
hazards, do not open this enclosure.
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the top cover. See
“
Top Cover
”
earlier in this chapter.
3.
Disconnect all cables from the power switch and cable assembly.
4.
Remove the single T-15 screw that secures the power switch and cable assembly to the
chassis
.
5.
Slide the power switch back
, then lift it out of the chassis
.
1
2
3
Figure 2-17.
Removing the power switch and cable assembly
Reverse steps 1 through 5 to replace the power switch and cable assembly.