Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 27

Side Access Panel, Remove any installed boards. Place them on a non-conductive work surface.

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2-16 Removal and Replacement Procedures The riser board with tray is removed for replacement and to access the expansion board slots or the riser board connectors. To remove the riser board with tray: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Disconnect all cables from the expansion boards. 4. Remove the side access panel. See "Side Access Panel" earlier in this chapter. 5. Remove any installed boards. Place them on a non-conductive work surface. 6. Remove the retaining screws. 7. Slide the riser board out the side of the chassis. Figure 2-14. Removing the riser board Reverse steps 1 through 7 to replace the riser board with tray. Reinstall any boards removed in step 4 into the same slots from which they were removed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-16
Removal and Replacement Procedures
The riser board with tray is removed for replacement and to access the expansion board slots or
the riser board connectors.
To remove the riser board with tray:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the top access panel. See
“
Top Access Panel
”
earlier in this chapter.
3.
Disconnect all cables from the expansion boards.
4.
Remove the side access panel. See
“
Side Access Panel
”
earlier in this chapter.
5.
Remove any installed boards. Place them on a non-conductive work surface.
6.
Remove the retaining screws.
7.
Slide the riser board out the side of the chassis.
Figure 2-14.
Removing the riser board
Reverse steps 1 through 7 to replace the riser board with tray. Reinstall any boards removed in
step 4 into the same slots from which they were removed.