Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 21

Non-Hot-Plug Drive Cage, CAUTION

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

2-10 Removal and Replacement Procedures Non-Hot-Plug Drive Cage The non-hot-plug drive cage is removed for replacement or to access the non-hot-plug hard drives. To remove the non-hot-plug drive cage: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Unlock and remove the front bezel door. See "Front Bezel Door" earlier in this chapter. 3. Remove the left side access panel. See "Left Side Access Panel" earlier in this chapter. 4. Disconnect all cables from any installed drives in the drive cage. 5. Remove the four T-15 screws that secure the drive cage to the chassis. 6. Slide the drive cage out the front of the chassis. Figure 2-7. Removing the non-hot-plug drive cage Reverse steps 1 through 6 to replace the non-hot-plug drive cage. CAUTION: Make sure that all power and signal cables to the non-hot-plug drive cage have been reseated properly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-10
Removal and Replacement Procedures
Non-Hot-Plug Drive Cage
The non-hot-plug drive cage is removed for replacement or to access the non-hot-plug
hard drives.
To remove the non-hot-plug drive cage:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Unlock and remove the front bezel door. See
“
Front Bezel Door
”
earlier in this chapter.
3.
Remove the left side access panel. See
“
Left Side Access Panel
”
earlier in this chapter.
4.
Disconnect all cables from any installed drives in the drive cage.
5.
Remove the four T-15 screws that secure the drive cage to the chassis.
6.
Slide the drive cage out the front of the chassis.
Figure 2-7.
Removing the non-hot-plug drive cage
Reverse steps 1 through 6 to replace the non-hot-plug drive cage.
CAUTION:
Make sure that all power and signal cables to the non-hot-plug drive
cage have been reseated properly.