Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 32

Processor Retention Bracket, Remove the processor from the system board. See

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2-21 Processor Retention Bracket The processor retention bracket is removed for replacement or to replace the system board. To remove the processor retention bracket: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the processor from the system board. See "Processor" earlier in this chapter. 3. Remove the four T-15 screws, then lift the processor retention bracket from the system board. Figure 2-19. Removing the processor retention bracket. Reverse steps 1 through 3 to replace the processor retention bracket. Compaq ProLiant 800 Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-21
Compaq ProLiant 800 Servers Maintenance and Service Guide
Processor Retention Bracket
The processor retention bracket is removed for replacement or to replace the system board.
To remove the processor retention bracket:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the processor from the system board. See
“
Processor
”
earlier in this chapter.
3.
Remove the four T-15 screws, then lift the processor retention bracket from the
system board.
Figure 2-19.
Removing the processor retention bracket.
Reverse steps 1 through 3 to replace the processor retention bracket.