D-Link 1824i User Guide - Page 52

tftp only, bootp-tftp, Boot Server IP Address, Boot File Name

Get D-Link 1824i - Hub - EN PDF manuals and user guides
UPC - 790069210358
View all D-Link 1824i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

10BASE-T Stackable Hubs ♦ Boot Server IP Address The IP address of the TFTP server where the configuration file is located. This entry is used only if the S/W Update Control is enabled and your boot protocol is tftp only; if you are using bootp-tftp mode, or if Send BOOTP Request on Power Up is enabled, the address will be obtained from the BOOTP server. ♦ Boot File Name The pathname of the configuration file on your TFTP server. If you are using SNMP-View as your TFTP server, this is the pathname of the .CFG file on your hard disk. This entry is used only if your boot protocol is TFTP ONLY; if you are using BOOTP&TFTP mode, or if Use Bootp to get IP after start up is enabled, the pathname will be obtained from the BOOTP server. For more information about SNMP configuration files, consult Appendix C. For detailed information about using the TFTP and BOOTP servers, consult the SNMP-View User's Guide. Figure 6 -6 Software Update Menu 6-10 Using the Console Interface

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
10BASE-T Stackable Hubs
♦
Boot Server IP Address
The IP address of the TFTP server where
the configuration file is located. This entry is used only if the
S/W
Update Control
is enabled and your boot protocol is
tftp only
; if
you are using
bootp-tftp
mode, or if
Send BOOTP Request on
Power Up
is enabled, the address will be obtained from the BOOTP
server.
♦
Boot File Name
The pathname of the configuration file on your
TFTP server.
If you are using SNMP-View as your TFTP server, this
is the pathname of the
.CFG
file on your hard disk.
This entry is
used only if your boot protocol is TFTP ONLY; if you are using
BOOTP&TFTP mode, or if
Use Bootp to get IP after start up
is
enabled, the pathname will be obtained from the BOOTP server.
For more information about SNMP configuration files, consult Appendix C.
For detailed information about using the TFTP and BOOTP servers, consult
the SNMP-View User’s Guide.
Figure 6 -6
Software Update Menu
6-10
Using the Console Interface