D-Link DPH-80 Manual - Page 60

Ethernet Transmit Test, Ethernet Receive Test

Get D-Link DPH-80 PDF manuals and user guides View all D-Link DPH-80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Using Session Initiated Protocol (SIP) SIP Production Test Ethernet Transmit Test In this test, packets containing 1 to 100mbps are transmitted and continue to be transmitted until the user ends the test by pressing any valid key on the keypad. This test does not play any tone, since the SIP phone cannot check if the test is successful. Ethernet Receive Test In this test a packet that is sent from the Ethernet driver is received back and is verified. If the test is successful, Success will appear in the browser; otherwise an Error message appears. It will take some time for Success or Error to appear, as it takes some time for the driver to receive the packet from network. The user must use a 100 Mbps Switch (full duplex mode) and connect any two ports for loop-back. Note: The user can press '0' to repeat the test, or '1' to exit the production test mode. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
60
Using Session Initiated Protocol (SIP)
SIP Production Test
In this test, packets containing 1 to 100mbps are transmitted and continue to
be transmitted until the user ends the test by pressing any
valid
key on the
keypad. This test does not play any tone, since the SIP phone cannot check if
the test is successful.
Ethernet Transmit Test
In this test a packet that is sent from the Ethernet driver is received back and is
verified. If the test is successful,
Success
will appear in the browser; otherwise
an
Error
message appears. It will take some time for
Success
or
Error
to ap-
pear, as it takes some time for the driver to receive the packet from network.
The user must use a
100 Mbps Switch (full duplex mode)
and connect any two
ports for loop-back.
Note: The user can press ‘0’ to repeat the test, or ‘1’ to exit the production test
mode.
Ethernet Receive Test