D-Link DPH-80 Manual - Page 84

H.323 Production Test

Get D-Link DPH-80 PDF manuals and user guides View all D-Link DPH-80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Using H.323 Protocol H.323 Troubleshooting Other Functions The factory default key sequence is entered, but there is no response. You must restart the phone. The production test key sequence is entered, but there is no response. You must restart the phone. The H.323 phone will exit the production test mode on the next restart. The remote upgrade key sequence is entered, but there is no response. You must have the software files in the TFTP server and the H.323 phone should be configured with the correct TFTP server and file names. The remote upgrade key sequence is entered, and the phone plays an unidentified tone. The H.323 phone plays a tone during the software download. The H.323 phone will restart upon successful download. There is a power out during the remote upgrade. If anything goes wrong during the software upgrade, the phone will use the previous existing software. H.323 Production Test This section describes the production test supported by the D-Link H.323 phone. The main hardware blocks to be tested are (i) LED, (ii) Key Scan, (iii) Hook Switch, (iv) Codec & Handset, (v) Speaker, (vi) Memory and (vii) Ethernet MAC and PHY. If a test is successful, the H.323 phone will play a Success tone and turn on the Green LED. If a test fails, it will play an Error tone and turn on the Red LEDs. After each test, press '1' to continue on to the next test and '0' to repeat the test. Note: In some tests the H.323 phone cannot determine the outcome of the test and the user must verify it. In such test cases the phone will not play any tone. 84

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
84
The factory default key sequence is entered, but there is no response.
You must restart the phone.
The production test key sequence is entered, but there is no response.
You must restart the phone. The H.323 phone will exit the production test mode
on the next restart.
The remote upgrade key sequence is entered,
but there is no response.
You must have the software files in the TFTP server and the H.323 phone
should be configured with the correct TFTP server and file names.
The remote upgrade key sequence is entered, and the phone plays an
unidentified tone.
The H.323 phone plays a tone during the software download. The H.323 phone
will restart upon successful download.
There is a power out during the remote upgrade.
If anything goes wrong during the software upgrade, the phone will use the
previous existing software.
Other Functions
Using H.323 Protocol
H.323 Troubleshooting
H.323 Production Test
This section describes the production test supported by the D-Link H.323
phone. The main hardware blocks to be tested are (i) LED, (ii) Key Scan, (iii)
Hook Switch, (iv) Codec & Handset, (v) Speaker, (vi) Memory and (vii) Ethernet
MAC and PHY. If a test is successful, the H.323 phone will play a
Success
tone
and turn on the
Green
LED. If a test fails, it will play an
Error
tone and turn on
the
Red
LEDs. After each test, press ‘1’ to continue on to the next test and ‘0’ to
repeat the test.
Note: In some tests the H.323 phone cannot determine the outcome of the test
and the user must verify it. In such test cases the phone will not play any tone.