Dell 1450 Dell Projector 1220/ Users Guide - Page 43

Guiding Signals, Fault - DC

Page 43 highlights

Guiding Signals Projector Status Description Control Buttons Power Standby mode Warming up mode Lamp on Cooling mode Projector overheated Lamp driver overheated Fan breakdown Lamp driver breakdown Color Wheel breakdown Lamp failure Fault - DC supply (+12V) Lamp module connection failed Projector in Standby mode. Ready to power on. Projector takes some time to warm up and power on. Projector in Normal mode, ready to display an image. Note: The OSD menu is not accessed. Projector is cooling to shutdown. Air vents might be blocked or ambient temperature may be above 35 °C. The projector automatically shuts down. Ensure that the air vents are not blocked and that the ambient temperature is within operational range. If the problem persists, contact Dell. The lamp driver is overheated. The air vents may be blocked. The projector automatically shuts down. Turn the display on again after the projector cools down. If the problem persists, contact Dell. One of the fans has failed. The projector automatically shuts down. If the problem persists, contact Dell. The lamp driver has failed. The projector automatically shuts down. Unplug the power cord after three minutes and then turn the display on again. If this problem persists, contact Dell. Color wheel cannot start. The projector has failed and the projector automatically shuts down. Unplug the power cord after three minutes and then turn on the projector. If this problem persists, contact Dell. Lamp is defective. Replace the lamp. Power supply has been interrupted. The projector automatically shuts down. Unplug the power cord after three minutes and then turn on the projector. If this problem persists, contact Dell. Lamp module connection may be disrupted. Check the lamp module and ensure that it is properly installed. If the problem persists, contact Dell. White Flashing White White White OFF AMBER OFF AMBER Flashing White OFF AMBER Flashing OFF Indicator TEMP (Amber) LAMP (Amber) OFF OFF OFF OFF OFF OFF OFF OFF AMBER OFF AMBER OFF AMBER Flashing OFF OFF AMBER Flashing AMBER Flashing AMBER Flashing OFF AMBER AMBER AMBER OFF AMBER Flashing Troubleshooting Your Projector 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

Troubleshooting Your Projector
43
Guiding Signals
Projector
Status
Description
Control Buttons
Indicator
Power
TEMP
(Amber)
LAMP
(Amber)
Standby
mode
Projector in Standby mode. Ready to
power on.
White Flashing
OFF
OFF
Warming up
mode
Projector takes some time to warm
up and power on.
White
OFF
OFF
Lamp on
Projector in Normal mode, ready to
display an image.
Note: The OSD menu is not
accessed.
White
OFF
OFF
Cooling
mode
Projector is cooling to shutdown.
White
OFF
OFF
Projector
overheated
Air vents might be blocked or
ambient temperature may be above
35 °C. The projector automatically
shuts down. Ensure that the air vents
are not blocked and that the ambient
temperature is within operational
range. If the problem persists,
contact Dell.
OFF
AMBER
OFF
Lamp driver
overheated
The lamp driver is overheated. The air
vents may be blocked. The projector
automatically shuts down. Turn the
display on again after the projector
cools down. If the problem persists,
contact Dell.
AMBER
AMBER
OFF
Fan
breakdown
One of the fans has failed. The
projector automatically shuts down.
If the problem persists, contact Dell.
OFF
AMBER
Flashing
OFF
Lamp driver
breakdown
The lamp driver has failed. The
projector automatically shuts down.
Unplug the power cord after three
minutes and then turn the display on
again. If this problem persists,
contact Dell.
AMBER Flashing
OFF
AMBER
Flashing
Color Wheel
breakdown
Color wheel cannot start. The
projector has failed and the projector
automatically shuts down. Unplug
the power cord after three minutes
and then turn on the projector. If this
problem persists, contact Dell.
White
AMBER
Flashing
AMBER
Flashing
Lamp failure
Lamp is defective. Replace the lamp.
OFF
OFF
AMBER
Fault - DC
supply (+12V)
Power supply has been interrupted.
The projector automatically shuts
down. Unplug the power cord after
three minutes and then turn on the
projector. If this problem persists,
contact Dell.
AMBER Flashing
AMBER
AMBER
Lamp module
connection
failed
Lamp module connection may be
disrupted. Check the lamp module
and ensure that it is properly
installed. If the problem persists,
contact Dell.
OFF
OFF
AMBER
Flashing