Dell 3100cn Color Laser Printer User's Guide - Page 68

Print Quality Problems

Get Dell 3100cn Color Laser Printer PDF manuals and user guides View all Dell 3100cn Color Laser Printer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Print media misfeeds or multiple feeds occur. Make sure the print media you are using meets the specifications for your printer. See "Print Media Supported" for more information. Flex print media before loading it in any of the sources. Make sure the print media is loaded correctly. Make sure the width and length guides on the print media sources are adjusted correctly. Do not overfill the print media sources. Do not force print media into the multipurpose feeder when you load it; otherwise, it may skew or buckle. Remove any curled print media from sources. Load the recommended print side correctly for the type of print media you are using. See "Loading Print Media in Standard and Optional Trays" for more information. Turn the print media over or around and try printing again to see if feeding improves. Do not mix print media types. Do not mix reams of print media. Remove the top and bottom sheets of a ream before loading the print media. Load a print media source only when it is empty. Envelope misfeeds or multiple feeds Remove the stack of envelopes from the multipurpose feeder. occur. Page breaks in unexpected places. Check the Job Timeout in the Basic Settings menu. Increase the setting. Job prints from the wrong source or Check the Paper Size and Paper Type in the Tray Settings menu on the printer operator panel and in the printer on the wrong print media. driver. Print media does not stack neatly in Turn the print media stack over in the tray or multipurpose feeder. the output bin. Printer does not duplex pages. Make sure Duplex is selected in both the PCL (Printer Control Language) menu on the printer operator panel and in the printer driver. Make sure you have enough printer memory installed. Print Quality Problems Problem Color is out of alignment. Action · The inside of printer is dirty. · If you install a new black cartridge and a ROS cleaning has not been done, this problem will happen. See "Cleaning Inside the Printer". Print is too light. · The toner may be low. Confirm the amount of the toner and change the toner cartridges if necessary. · Set the Draft Mode check box to off in the Advanced in the printer driver. · If you are printing on an uneven print surface, change the Paper Type settings in the Tray Settings menu. See "Paper Type." · Verify that the correct print media is being used. · The drum cartridge may need to be replaced. Change the drum cartridge. Toner smears or print comes off page. · If you are printing on an uneven print surface, change the Paper Type settings in the Tray Settings menu. See

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
Print Quality Problems
Print media misfeeds
or multiple feeds occur.
Make sure the print media you are using meets the specifications for your printer. See "
Print Media Supported
" for
more information.
Flex print media before loading it in any of the sources.
Make sure the print media is loaded correctly.
Make sure the width and length guides on the print media sources are adjusted correctly.
Do not overfill the print media sources.
Do not force print media into the multipurpose feeder when you load it; otherwise, it may skew or buckle.
Remove any curled print media from sources.
Load the recommended print side correctly for the type of print media you are using. See "
Loading Print Media in
Standard and Optional Trays
" for more information.
Turn the print media over or around and try printing again to see if feeding improves.
Do not mix print media types.
Do not mix reams of print media.
Remove the top and bottom sheets of a ream before loading the print media.
Load a print media source only when it is empty.
Envelope misfeeds or multiple feeds
occur.
Remove the stack of envelopes from the multipurpose feeder.
Page breaks in unexpected places.
Check the
Job Timeout
in the
Basic Settings
menu. Increase the setting.
Job prints from the wrong source or
on the wrong print media.
Check the
Paper Size
and
Paper Type
in the
Tray Settings
menu on the printer operator panel and in the printer
driver.
Print media does not stack neatly in
the output bin.
Turn the print media stack over in the tray or multipurpose feeder.
Printer does not duplex pages.
Make sure
Duplex
is selected in both the
PCL (
Printer Control Language
)
menu on the printer operator panel and in
the printer driver.
Make sure you have enough printer memory installed.
Problem
Action
Color is out of alignment.
·
The inside of printer is dirty.
·
If you install a new black cartridge and a ROS cleaning has not been done, this problem will happen. See
"
Cleaning Inside the Printer
".
Print is too light.
·
The toner may be low. Confirm the amount of the toner and change the toner cartridges if necessary.
·
Set the
Draft Mode
check box to off in the Advanced in the printer driver.
·
If you are printing on an uneven print surface, change the
Paper Type
settings in the
Tray Settings
menu. See
"
Paper Type
."
·
Verify that the correct print media is being used.
·
The drum cartridge may need to be replaced. Change the drum cartridge.
Toner smears or print comes off page.
·
If you are printing on an uneven print surface, change the
Paper Type
settings in the
Tray Settings
menu. See