Dell Force10 Z9000 Installing the Z9000 System - Page 35

Access Ports, Access the RJ-45/RS-232 Console Port

Get Dell Force10 Z9000 PDF manuals and user guides View all Dell Force10 Z9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

7 Access Ports The Z9000 has two management ports available for system access-a console port and a Universal Serial Bus (USB)-B port. The USB-B ports act exactly the same as the console port. The terminal settings are the same for both access ports. Access the RJ-45/RS-232 Console Port On the I/O side of the Z9000 system, the RJ-45/RS-232 console port is labeled in the upper right-hand corner as shown in the following figure. Figure 7-1. RJ-45/RS-232 Console Port Connector Primary Management (Ethernet) Port RJ-45/RS-232 Console Port For the RJ-45/RS-232 console port pinout assignments, refer to Table 7-1. To access the RJ-45/RS-232 console port, follow these steps:. Step Task 1 Install an RJ-45 copper cable into the console port. Use a rollover cable to connect the Z9000 console port to a terminal server. 2 Connect the other end of the cable to the Data Terminal Equipment (DTE) serial port on the PC or terminal server. 3 Keep the default terminal settings on the console as follows: • 9600 baud rate • No parity • 8 data bits • 1 stop bit • No flow control Access Ports | 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Access Ports
|
35
7
Access Ports
The Z9000 has two management ports available for system access—a console port and a Universal Serial
Bus (USB)-B port. The USB-B ports act exactly the same as the console port. The terminal settings are
the same for both access ports.
Access the RJ-45/RS-232 Console Port
On the I/O side of the Z9000 system, the RJ-45/RS-232 console port is labeled in the upper right-hand
corner as shown in the following figure.
Figure 7-1.
RJ-45/RS-232 Console Port Connector
For the RJ-45/RS-232 console port pinout assignments, refer to
Table 7-1
.
To access the RJ-45/RS-232 console port, follow these steps:.
Step
Task
1
Install an RJ-45 copper cable into the console port. Use a rollover cable to connect the Z9000 console port to a
terminal server.
2
Connect the other end of the cable to the Data Terminal Equipment (DTE) serial port on the PC or terminal server.
3
Keep the default terminal settings on the console as follows:
•
9600 baud rate
•
No parity
•
8 data bits
•
1 stop bit
•
No flow control
RJ-45/RS-232
Console Port
Primary Management
(Ethernet) Port