Dell OptiPlex 3011 AIO Owner's Manual - Page 41

Enable Legacy Option ROMs, Enable UEFI Network Stack

Get Dell OptiPlex 3011 AIO PDF manuals and user guides View all Dell OptiPlex 3011 AIO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Option Advanced Boot Options Date/Time Table 3. System Configuration Option Integrated NIC Serial Port SATA Operation Drives Description • Exit - Exits and starts the computer. The Enable Legacy Option ROMs option will allow the legacy option ROMs to load, when in UEFI boot mode. Without this option, only UEFI option ROMs will load. This option is required for Legacy boot mode. This Legacy boot mode is not allowed when you enable the Secure Boot. By default, the Enable Legacy Option ROMs check-box is not selected. The other options are: • Load Defaults - Restores the default settings of the computer. • Apply - Enables you to apply the settings. • Exit - Exits and starts the computer. Allows you to set the date and time. The changes to the system date and time takes effect immediately. Description Allows you to enable or disable the integrated network card. You can set the integrated NIC to: • Disabled • Enabled • Enabled w/PXE (This option is selected by default) • Enabled w/ImageServer • Enable UEFI Network Stack NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear. Allows you to define the serial port settings. You can set the serial port to: • Disabled • COM1 (This option is selected by default) • COM2 • COM3 • COM4 NOTE: The operating system may allocate resources even though the setting is disabled. Allows you to configure the operating mode of the integrated SATA hard drive controller. • Disabled - The SATA controllers are hidden. • ATA - SATA is configured for ATA mode. • AHCI - SATA is configured for AHCI mode. This option is enabled by default. Allows you to enable or disable the various on-board drives: • SATA-0 • SATA-1 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Option
Description
•
Exit - Exits and starts the computer.
Advanced Boot Options
The Enable Legacy Option ROMs option will allow the legacy option ROMs to load,
when in UEFI boot mode. Without this option, only UEFI option ROMs will load. This
option is required for Legacy boot mode. This Legacy boot mode is not allowed when
you enable the Secure Boot. By default, the
Enable Legacy Option ROMs
check-box is
not selected. The other options are:
•
Load Defaults - Restores the default settings of the computer.
•
Apply - Enables you to apply the settings.
•
Exit - Exits and starts the computer.
Date/Time
Allows you to set the date and time. The changes to the system date and time takes
effect immediately.
Table 3. System Configuration
Option
Description
Integrated NIC
Allows you to enable or disable the integrated network card. You can set the
integrated NIC to:
•
Disabled
•
Enabled
•
Enabled w/PXE (This option is selected by default)
•
Enabled w/ImageServer
•
Enable UEFI Network Stack
NOTE:
Depending on the computer and its installed devices, the items listed in
this section may or may not appear.
Serial Port
Allows you to define the serial port settings. You can set the serial port to:
•
Disabled
•
COM1 (This option is selected by default)
•
COM2
•
COM3
•
COM4
NOTE:
The operating system may allocate resources even though the setting is
disabled.
SATA Operation
Allows you to configure the operating mode of the integrated SATA hard drive
controller.
•
Disabled
- The SATA controllers are hidden.
•
ATA
- SATA is configured for ATA mode.
•
AHCI
- SATA is configured for AHCI mode. This option is enabled by default.
Drives
Allows you to enable or disable the various on-board drives:
•
SATA-0
•
SATA-1
41