Dell PowerEdge R350 EMC Installation and Service Manual - Page 64

Installing the BOSS S2 module, Installing the BOSS S2 card carrier

Get Dell PowerEdge R350 PDF manuals and user guides View all Dell PowerEdge R350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

3. Connect the BOSS power cable and the BOSS signal cable to the system board. 4. Connect the BOSS module to the chassis by aligning with unlock sign. 5. Slide the BOSS S2 module in to the bay until it is firmly locked. 6. Using the Phillips #1 screwdriver, tighten the screw. Figure 57. Installing the BOSS S2 module 7. Slide the BOSS S2 card carrier into the BOSS S2 module slot. 8. Close the BOSS S2 card carrier release latch to lock the carrier in place. Figure 58. Installing the BOSS S2 card carrier Next steps 1. If removed, install the air shroud. 2. Follow the procedure listed in the After working inside your system. 64 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
3.
Connect the BOSS power cable and the BOSS signal cable to the system board.
4.
Connect the BOSS module to the chassis by aligning with unlock sign.
5.
Slide the BOSS S2 module in to the bay until it is firmly locked.
6.
Using the Phillips #1 screwdriver, tighten the screw.
Figure 57. Installing the BOSS S2 module
7.
Slide the BOSS S2 card carrier into the BOSS S2 module slot.
8.
Close the BOSS S2 card carrier release latch to lock the carrier in place.
Figure 58. Installing the BOSS S2 card carrier
Next steps
1.
If removed,
install the air shroud
.
2.
Follow the procedure listed in the
After working inside your system
.
64
Installing and removing system components