Dell PowerEdge R350 EMC Installation and Service Manual - Page 67

Installing the front mounting front PERC module

Get Dell PowerEdge R350 PDF manuals and user guides View all Dell PowerEdge R350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Figure 61. Removing the front mounting front PERC module Next steps Replace the front mounting front PERC module. Installing the front mounting front PERC module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If installed, remove the air shroud. 4. Route the cable properly to prevent the cable from being pinched or crimped. Steps 1. Connect the PERC cable to the front PERC module. 2. Align the front PERC module at an angle until the tray touches the slot in the system. 3. Press the front PERC module connector with the connector on the drive backplane until firmly seated. 4. Using a Phillips #2 screwdriver, tighten the thumbscrews on the front PERC module. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Installing and removing system components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Figure 61. Removing the front mounting front PERC module
Next steps
Replace the front mounting front PERC module
.
Installing the front mounting front PERC module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If installed,
remove the air shroud
.
4.
Route the cable properly to prevent the cable from being pinched or crimped.
Steps
1.
Connect the PERC cable to the front PERC module.
2.
Align the front PERC module at an angle until the tray touches the slot in the system.
3.
Press the front PERC module connector with the connector on the drive backplane until firmly seated.
4.
Using a Phillips #2 screwdriver, tighten the thumbscrews on the front PERC module.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Installing and removing system components
67